Jumpy III (from 2016)

Citroen Jumpy 3 | Tuning Accessories and LED Lights | QSPCARS

Active Filters

  • Color: 6.500K Ice White Light
  • Color: Anodized Steel
  • Color: Graphite Black
Car Roof Rack Basket Tray FOR CITROEN JUMPER JUMPY | Off Road Black STEEL Luggage CARRIER
  • -3%
Add to Wishlist
Car Roof Rack Basket Tray FOR CITROEN JUMPER JUMPY | Off Road...
COMPATIBILITY:

For CITROEN, with Roof Bars already Installed:

- CITROEN JUMPER
- CITROEN JUMPY


ASSEMBLY:

1) Join together the two parcels that make up the Luggage Rack
2) Screw them together using the appropriate screws
3) Secure the Luggage Carrier to the Roof Bars, using the 4x Brackets + Rubber Shims supplied




Although mouting is simple and intuitive, FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT.
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.
Add to Wishlist
€329.99 Regular Price €340.20
H7 LED Kit for Citroen Spacetourer, Jumpy 3 Low Beam CANbus Bulbs | 6500K Cool White 8000LM
  • -4%
Add to Wishlist
H7 LED Kit for Citroen Spacetourer, Jumpy 3 Low Beam CANbus...
COMPATIBILITY:

- For Lowbeam CITROEN SPACETOURER, Jumpy 3 (from 2016)

FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

- ADAPTERS:

All cars that do not have the STANDARD LOCKING CLIP to lock the halogen bulb, may need simple ADAPTERS; found them in OUR STORE.
IMPORTANT: Their compatibility could not always depend on the model of your car; it depends mainly on the LOCKING SYSTEM of the halogen bulbs of your headlight.
Add to Wishlist
€61.88 Regular Price €64.46
LED License Plate Lights CANbus for Citroen JUMPY 3 Van | 6500K Ice White Light, Plug & Play
  • -2%
  • Out of Stock
Add to Wishlist
LED License Plate Lights CANbus for Citroen JUMPY 3 Van |...
COMPATIBILITY:

CITROEN:

- Jumpy 3 Van (from 2016)

** ATTENTION: Only for Versions with 2 Rear Doors **


INSTRUCTION:

- Remove the current led plates, using a screwdriver if necessary, inserting the tip in the side part of the plate and apply pressure towards the outside: the plate will come out./ If Screws present Remove them by unscrewing them to release the plate

- Disconnect the cable and disconnect definitely the plate.

- Connect the new LED PLATE to the cable and replace it inside the housing. Repeat the same operation with the second plate.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES
Add to Wishlist
€23.41 Regular Price €23.89
2 LED License Plate Lights for CITROEN JUMPY 3 | CANbus, Plug & Play | 18 Leds 6500K Cool White
  • -3%
  • Out of Stock
Add to Wishlist
2 LED License Plate Lights for CITROEN JUMPY 3 | CANbus, Plug...
COMPATIBILITY:

- Citroen Jumpy 3 (from 2016)

** ATTENTION: Only for Versions with 1 Rear Door **


ASSEMBLY INSTRUCTIONS:

- Remove the current plates, using a screwdriver if necessary, inserting the tip into the lateral part of the plate and pressing towards the outside: the plate will release and come out.

- Disconnect the cable and finally detach the plate.

- Connect the new LED PLATE to the cable and reposition it inside the housing. Repeat the same operation with the second plate.




FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES
Add to Wishlist
€22.20 Regular Price €22.89
Front LICENSE PLATE Holder for Citroen Bracket SIDE RELOCATOR In Anodized STEEL tuning
  • -1%
Add to Wishlist
Front LICENSE PLATE Holder for Citroen Bracket SIDE RELOCATOR...
COMPATIBILITY:

- For CITROEN Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

Add to Wishlist
€19.06 Regular Price €19.25