California - T (08-18)

COMPATIBILITY:

- It Can be Installed on Ferrari California, with Roof Bars (already installed), with a Minimum Load Capacity of 90kg


- IF ROOF BARS HAVE A CAPACITY OF 90KG, CAN THEY SUPPORT THE TENT, WHICH WEIGHS 90KG + THE WEIGHT OF THE PEOPLE WHO WILL HOST IT?

The maximum weight capacity supplied when purchasing a pair of roof bars always represents the dynamic capacity of the bars, i.e. the maximum capacity of the same when the vehicle is moving, but all the bars, in addition to having a dynamic capacity, have a static capacity, which in most cases it is not reported on the bars.

The Static Capacity Represents the Maximum Weight Capacity of the Roof Bars with the Vehicle Stationary, and on average the latter Reaches Approximately X3 Times the Dynamic Capacity.


- CAN ALL CARS HOLD A ROOF TENT?

Absolutely Yes. The side members of each car are designed to support more than the weight of the car itself, since, in the event of an accident and the car overturning, for safety reasons, it must support its own weight.

Since the smallest of the cars weighs at least 1 Ton, by logic, it is obvious that any car (even the smallest!) can hold both the roof tent and its guests inside, without any problem.


ASSEMBLY:

- Place the tent on the roof bars of your vehicle (2 people min.)
- Under the tent there are 2 channels, insert 4 steel inserts crossed by the bolt for each channel
- Scrolling through the inserts equipped with bolts, match 2 bolts, one with the outside and one with the inside of the roof rack
- Mount the bracket supplied by gripping the part underneath the roof rack and tighten the bolts
- Remember to Tighten the Bolts Whenever You Travel.


OPENING:

- Press on the Steel Jack Closure Buckles that block the Closure Laces
- Accompany the automated opening upwards
- USEFUL ADVICE: We recommend leaving the door and window zips open for quick and easy opening and closing of the tent
- The closure occurs through long laces designed for draft from the ground



Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY

- For Ferrari California


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY

- For Ferrari California


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY

- For Ferrari California


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY

Jump Starter Mode (Emergency Start-up):

- Cars (including Ferrari), Motorcycles, Pic ups, Suvs, Commercial Vehicles and Boats
- Petrol, Diesel, Hybrid, Start and Stop Engines
- Petrol Engines up to 8.000cc Displacement, Diesel Engines up to 7.000cc Displacement

Power Bank Mode (Portable Charger):

- Any 12V electrical or electronic accessory or appliance, including Apple devices


JUMP STARTER USE:

- Access the Battery Compartment of your Ferrari (or of the Motorcycle or Watercraft)
- Connect the Wiring Harness that has the two Pliers (Red and Black) at one end, and the Blue Plug at the other, to the Jump Starter
- Switch on the Jump Stater By pressing the only available button, to check the charge status
- Connect the Red Pliers to the Positive Pole, the Black Pliers to the Negative Pole (NO FEAR, if you make a mistake there will be NO sparks)
- After the connection, press the only button on the transformer of the Harness, if connected correctly a green light will turn on; if it is red, invert the polarity or check the clamp connection and press the button again
- A green light proceed with starting the vehicle

POWERBANK USE:

- Connect the cable needed to power the device you want to charge to a USB or USB-C socket and press the power button
- Wireless recharge, place a device designed for this recharge on the lightning bolt design on the Power Bank and press the power button
- The recharge or flow of current through the cigarette lighter takes place by connecting the DC plug, which has the cigarette lighter input at the end; Therefore insert the cigarette lighter socket and press the ignition button




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY:

- On bodywork, rubber, plastics, metals, leather, fabrics, glass of your Ferrari
- All Products Can Be Used on Previously Treated or Waxed Bodywork without worrying about damaging any layers


RECOMMENDED TOTALITARY APPLICATION:

1 APPROXIMATE BODYWORK WASH WITH: Gloss Shampoo (GLOSS SHAMPOO)
- Dilute 20Ml of Shampoo for 10Lt of Water
- Apply Evenly and Wash with a High Quality Sponge or Brush removing Dirt and Residue
- Rinse with Clean Water
- Dry by buffing with a clean microfiber cloth or quality chamois leather

2 BODYWORK WASH FINISHING WITH: Waterless Car Wash (WATERLESS CAR WASH)
- Spray evenly on the surface to be treated
- Rub with a microfibre cloth to remove dirt and residues
- After 30-60 Seconds, Buff The Area With A Clean Microfiber Cloth

3 WHEEL WASHING WITH: Rim Cleaner (WHEEL CLEANER - FELGENREINIGER)
- Spray evenly on the surface to be treated
- Leave to act without removing it
- Remove Dirt gently with a Sponge or Rim Brush
- Rinse after about 2 minutes

4 BODYWORK POLISHING WITH: Hydro Wax (QUICK SHINE WAX)
- Then at the end of the car wash, spray evenly on the surface to be treated
- Wait 60 Seconds
- Polish the area with a clean microfiber cloth

5 NANOTECHNOLOGY WITH: Nanotechnological Hydro Wax (HYDRO ARMOR)
- With a dry and thoroughly washed vehicle
- Dilute 50ml of Nanotechnological Hydro Wax in 450ml of water
- Apply the product with a professional sponge
- Rinse with Clean Water
- Polish with a clean microfiber cloth

6 CLEAN THE GLASSES AND MIRRORS WITH: Antistatic Glass Cleaner (GLASS CLEANER SPRAY)
- Spray a small amount on the glass to be treated
- Rub with a Microfiber Cloth Removing Dirt and Residues
- Polish the area with a second clean microfiber cloth

7 PLASTIC CLEANING OR LEATHER TREATMENT WITH: Leather, Plastic and Vinyl Interior Treatment (INTERIOR SPRAY)
- Spray evenly on the surface to be treated
- Rub with a microfibre cloth to remove dirt and residues
- Polish The Area With A Clean Microfiber Cloth

8 CLEANING CARPET OR CLOTH SEATS WITH: Fabrics and Matts Cleaner Spray (CARPET AND TEXTILE CLEANER)
- Spray evenly on the surface to be treated
- Wait a few seconds
- Absorb the liquid with a clean microfiber cloth
- To remove stains, leave it to act for a few minutes
- Absorb the liquid with a microfiber cloth
- Repeat several times until the Stain disappears

9 TIRE SHINE WITH: Black Tire Shine Protective Concentrate (REIFENSHUTZ - TIRE PROTECT)
- Checking that you have thoroughly cleaned the tires before application
- Dilute 50Ml of Concentrate in 200Ml of Water in a Plastic Bucket
- Apply the product with a sponge, cloth or brush
- Wait for Drying



Even if simple and intuitive FOR OPTIMAL USE, WE ALWAYS RECOMMEND THE APPLICATION OF OUR PRODUCTS BY AN EXPERT, Always Checking The Risk Label relating to Dangerous Substances, as any form of Contact could be dangerous. We trust in your common sense.

We do not assume responsibility for: erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, to third parties, to the Vehicle or to the article itself, as we describe every single specification in detail.

COMPATIBILITY:

ATTENTION: in Italy application is only permitted on rear windows and rear windshields. We invite you to check the individual regulations of each state.

- For Ferrari California (All Versions and Years)
- Pre-cut, non-shaped pieces, 10% Larger in size, capable of covering all rear windows


APPLICATION:

- In addition to the film for the application you will need: Spatula, Cutter, Water and Fabric Softener, Nebulizer, Hairdryer or Heat Gun.
- The film must always be applied internally to the glass, however the external part is also necessary, which is fundamental for shaping and modeling the film before the final application on the internal part.

- Cut the film with a good margin compared to the size of the glass to be darkened (3-5cm).
- Thoroughly clean the glass internally and externally 2-3 times.
- Spray the mixture of water and softener mixed in a ratio of 1:10 on the outside of the glass.
- Apply the Film Externally to the Glass, Keeping the adhesive part of the Film facing towards you.
- Imprint the Film on the External Glass with the Spatula Forming a Large H.
- Shape the Film Using a Hairdryer and Spatula. The objective is to remove all the bubbles by making the Film adhere perfectly to the External Glass.
(the better it is processed now the easier it will be to move and apply the film internally later)
- Once the film is completely adhered without bubbles, shape it with the cutter by cutting off the excess, remaining within the margin of 2-3mm from the edge of the glass.
- Still leaving the film on the outside of the glass, make sure again that the inside of the glass is clean and proceed to spray the solution of water and softener inside the glass.
- Remove the protective film on the adhesive area of the film. Help yourself to remove it by spraying more water and fabric softener.
- Move the film to the inside of the glass, this time with the adhesive part facing the glass itself.
- Shape and flatten the film with the spatula, removing bubbles and liquid. (if the hairdryer has been used previously it will not be needed now)

- The glasses are operational after 24 hours
- Final adhesion is achieved after approximately 15 - 20 days at 18° C and in dry climate conditions.


MAINTENANCE AND CLEANING
Use high-quality cleaners specifically for glass surfaces. The cleaning system (cloth, sponge, etc.) must be wet and not abrasive with a pH value between 6 and 8 (neither too acidic nor too alkaline).


Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY:

ATTENTION: in Italy application is only permitted on rear windows and rear windshields. We invite you to check the individual regulations of each state.

- For Ferrari California (All Versions and Years)
- Pre-cut, non-shaped pieces, 10% Larger in size, capable of covering all rear windows


APPLICATION:

- In addition to the film for the application you will need: Spatula, Cutter, Water and Fabric Softener, Nebulizer, Hairdryer or Heat Gun.
- The film must always be applied internally to the glass, however the external part is also necessary, which is fundamental for shaping and modeling the film before the final application on the internal part.

- Cut the film with a good margin compared to the size of the glass to be darkened (3-5cm).
- Thoroughly clean the glass internally and externally 2-3 times.
- Spray the mixture of water and softener mixed in a ratio of 1:10 on the outside of the glass.
- Apply the Film Externally to the Glass, Keeping the adhesive part of the Film facing towards you.
- Imprint the Film on the External Glass with the Spatula Forming a Large H.
- Shape the Film Using a Hairdryer and Spatula. The objective is to remove all the bubbles by making the Film adhere perfectly to the External Glass.
(the better it is processed now the easier it will be to move and apply the film internally later)
- Once the film is completely adhered without bubbles, shape it with the cutter by cutting off the excess, remaining within the margin of 2-3mm from the edge of the glass.
- Still leaving the film on the outside of the glass, make sure again that the inside of the glass is clean and proceed to spray the solution of water and softener inside the glass.
- Remove the protective film on the adhesive area of the film. Help yourself to remove it by spraying more water and fabric softener.
- Move the film to the inside of the glass, this time with the adhesive part facing the glass itself.
- Shape and flatten the film with the spatula, removing bubbles and liquid. (if the hairdryer has been used previously it will not be needed now)

- The glasses are operational after 24 hours
- Final adhesion is achieved after approximately 15 - 20 days at 18° C and in dry climate conditions.


MAINTENANCE AND CLEANING
Use high-quality cleaners specifically for glass surfaces. The cleaning system (cloth, sponge, etc.) must be wet and not abrasive with a pH value between 6 and 8 (neither too acidic nor too alkaline).


Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY:

ATTENTION: in Italy application is only permitted on rear windows and rear windshields. We invite you to check the individual regulations of each state.

- For Ferrari California (All Versions and Years)
- Pre-cut, non-shaped pieces, 10% Larger in size, capable of covering all rear windows


APPLICATION:

- In addition to the film for the application you will need: Spatula, Cutter, Water and Fabric Softener, Nebulizer, Hairdryer or Heat Gun.
- The film must always be applied internally to the glass, however the external part is also necessary, which is fundamental for shaping and modeling the film before the final application on the internal part.

- Cut the film with a good margin compared to the size of the glass to be darkened (3-5cm).
- Thoroughly clean the glass internally and externally 2-3 times.
- Spray the mixture of water and softener mixed in a ratio of 1:10 on the outside of the glass.
- Apply the Film Externally to the Glass, Keeping the adhesive part of the Film facing towards you.
- Imprint the Film on the External Glass with the Spatula Forming a Large H.
- Shape the Film Using a Hairdryer and Spatula. The objective is to remove all the bubbles by making the Film adhere perfectly to the External Glass.
(the better it is processed now the easier it will be to move and apply the film internally later)
- Once the film is completely adhered without bubbles, shape it with the cutter by cutting off the excess, remaining within the margin of 2-3mm from the edge of the glass.
- Still leaving the film on the outside of the glass, make sure again that the inside of the glass is clean and proceed to spray the solution of water and softener inside the glass.
- Remove the protective film on the adhesive area of the film. Help yourself to remove it by spraying more water and fabric softener.
- Move the film to the inside of the glass, this time with the adhesive part facing the glass itself.
- Shape and flatten the film with the spatula, removing bubbles and liquid. (if the hairdryer has been used previously it will not be needed now)

- The glasses are operational after 24 hours
- Final adhesion is achieved after approximately 15 - 20 days at 18° C and in dry climate conditions.


MAINTENANCE AND CLEANING
Use high-quality cleaners specifically for glass surfaces. The cleaning system (cloth, sponge, etc.) must be wet and not abrasive with a pH value between 6 and 8 (neither too acidic nor too alkaline).


Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY:

- Ferrari California - T (08-18), with Tires:

245/40 R19
245/35 R20
285/35 R20

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY:

- Specific for Ferrari California


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- FERRARI CALIFORNIA - CALIFORNIA T (2008-2018) WITH STANDARD XENON SYSTEM


MOUNTING:

- Replace the original bulbs by connecting the NEW REPLACEMENT BULBS


FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT

COMPATIBILITY:

- Specific for Ferrari California


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Ferrari California - T (08-18), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- FERRARI

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- FERRARI

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- FERRARI

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- FERRARI

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Suitable for FERRARI Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for FERRARI Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for FERRARI Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- For FERRARI Cars

It is applicable on any vehicle with an Indentation on the bumper where it will be possible to fix the bracket (LOOK AT THE PHOTO).



ASSEMBLY:

- Put the plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the Screws

- Remove the plate and apply it on the new plate holder

- Apply the chromed frame and Fix it with the 4 screws supplied




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For FERRARI Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.