850 (64-71)

COMPATIBILITY

- For FIAT 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56


FOR OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT

- the Headlamp has H4 or H13 socket, therefore in 90% of the cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (link only) will be valid




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY

- For Fiat 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56


FOR OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

- the headlight has an H4 or H13 socket, therefore in 90% of cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule will apply (connection only)



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.
We also remind you that these are Aftermarket Items, designed for Full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For Fiat 850 (64-71)


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY

- For FIAT 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56

FOR OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT

- the Headlamp has H4 or H13 socket, therefore in 90% of the cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (link only) will be valid




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY:

- For Fiat 850 (64-71)


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY

- For Fiat 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56


FOR OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

- the headlight has an H4 or H13 socket, therefore in 90% of cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule will apply (connection only)



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.
We also remind you that these are Aftermarket Items, designed for Full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY

- For Fiat 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56


FOR OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

- the headlight has an H4 or H13 socket, therefore in 90% of cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule will apply (connection only)



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.
We also remind you that these are Aftermarket Items, designed for Full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY

- For FIAT 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56

FOR OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT

- the Headlamp has H4 or H13 socket, therefore in 90% of the cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (link only) will be valid




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY

- For FIAT 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56

FOR OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT

- the Headlamp has H4 or H13 socket, therefore in 90% of the cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (link only) will be valid




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY

Jump Starter Mode (Emergency Start-up):

- Cars (including Fiat), Motorcycles, Pic ups, Suvs, Commercial Vehicles and Boats
- Petrol, Diesel, Hybrid, Start and Stop Engines
- Petrol Engines up to 8.000cc Displacement, Diesel Engines up to 7.000cc Displacement

Power Bank Mode (Portable Charger):

- Any 12V electrical or electronic accessory or appliance, including Apple devices


JUMP STARTER USE:

- Access the Battery Compartment of your Fiat (or of the Motorcycle or Watercraft)
- Connect the Wiring Harness that has the two Pliers (Red and Black) at one end, and the Blue Plug at the other, to the Jump Starter
- Switch on the Jump Stater By pressing the only available button, to check the charge status
- Connect the Red Pliers to the Positive Pole, the Black Pliers to the Negative Pole (NO FEAR, if you make a mistake there will be NO sparks)
- After the connection, press the only button on the transformer of the Harness, if connected correctly a green light will turn on; if it is red, invert the polarity or check the clamp connection and press the button again
- A green light proceed with starting the vehicle

POWERBANK USE:

- Connect the cable needed to power the device you want to charge to a USB or USB-C socket and press the power button
- Wireless recharge, place a device designed for this recharge on the lightning bolt design on the Power Bank and press the power button
- The recharge or flow of current through the cigarette lighter takes place by connecting the DC plug, which has the cigarette lighter input at the end; Therefore insert the cigarette lighter socket and press the ignition button




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Fiat 124, 850

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Fiat 124, 850

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Fiat 124, 850

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY

- For FIAT 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56

FOR OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT

- the Headlamp has H4 or H13 socket, therefore in 90% of the cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (link only) will be valid




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY:

- For FIAT 850 (1964-1971)

- Code of compatibility with other headlights: 6014; 6015; 6016; H6024; PAR56

FOR OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT

- the Headlamp has H4 or H13 socket, therefore in 90% of the cases, it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (link only) will be valid




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Fiat 124, 850

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Fiat 124, 850

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Fiat 124, 850

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- On bodywork, rubber, plastics, metals, leather, fabrics, glass of your Fiat
- All Products Can Be Used on Previously Treated or Waxed Bodywork without worrying about damaging any layers


RECOMMENDED TOTALITARY APPLICATION:

1 APPROXIMATE BODYWORK WASH WITH: Gloss Shampoo (GLOSS SHAMPOO)
- Dilute 20Ml of Shampoo for 10Lt of Water
- Apply Evenly and Wash with a High Quality Sponge or Brush removing Dirt and Residue
- Rinse with Clean Water
- Dry by buffing with a clean microfiber cloth or quality chamois leather

2 BODYWORK WASH FINISHING WITH: Waterless Car Wash (WATERLESS CAR WASH)
- Spray evenly on the surface to be treated
- Rub with a microfibre cloth to remove dirt and residues
- After 30-60 Seconds, Buff The Area With A Clean Microfiber Cloth

3 WHEEL WASHING WITH: Rim Cleaner (WHEEL CLEANER - FELGENREINIGER)
- Spray evenly on the surface to be treated
- Leave to act without removing it
- Remove Dirt gently with a Sponge or Rim Brush
- Rinse after about 2 minutes

4 BODYWORK POLISHING WITH: Hydro Wax (QUICK SHINE WAX)
- Then at the end of the car wash, spray evenly on the surface to be treated
- Wait 60 Seconds
- Polish the area with a clean microfiber cloth

5 NANOTECHNOLOGY WITH: Nanotechnological Hydro Wax (HYDRO ARMOR)
- With a dry and thoroughly washed vehicle
- Dilute 50ml of Nanotechnological Hydro Wax in 450ml of water
- Apply the product with a professional sponge
- Rinse with Clean Water
- Polish with a clean microfiber cloth

6 CLEAN THE GLASSES AND MIRRORS WITH: Antistatic Glass Cleaner (GLASS CLEANER SPRAY)
- Spray a small amount on the glass to be treated
- Rub with a Microfiber Cloth Removing Dirt and Residues
- Polish the area with a second clean microfiber cloth

7 PLASTIC CLEANING OR LEATHER TREATMENT WITH: Leather, Plastic and Vinyl Interior Treatment (INTERIOR SPRAY)
- Spray evenly on the surface to be treated
- Rub with a microfibre cloth to remove dirt and residues
- Polish The Area With A Clean Microfiber Cloth

8 CLEANING CARPET OR CLOTH SEATS WITH: Fabrics and Matts Cleaner Spray (CARPET AND TEXTILE CLEANER)
- Spray evenly on the surface to be treated
- Wait a few seconds
- Absorb the liquid with a clean microfiber cloth
- To remove stains, leave it to act for a few minutes
- Absorb the liquid with a microfiber cloth
- Repeat several times until the Stain disappears

9 TIRE SHINE WITH: Black Tire Shine Protective Concentrate (REIFENSHUTZ - TIRE PROTECT)
- Checking that you have thoroughly cleaned the tires before application
- Dilute 50Ml of Concentrate in 200Ml of Water in a Plastic Bucket
- Apply the product with a sponge, cloth or brush
- Wait for Drying



Even if simple and intuitive FOR OPTIMAL USE, WE ALWAYS RECOMMEND THE APPLICATION OF OUR PRODUCTS BY AN EXPERT, Always Checking The Risk Label relating to Dangerous Substances, as any form of Contact could be dangerous. We trust in your common sense.

We do not assume responsibility for: erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, to third parties, to the Vehicle or to the article itself, as we describe every single specification in detail.

COMPATIBILITY:

ATTENTION: in Italy application is only permitted on rear windows and rear windshields. We invite you to check the individual regulations of each state.

- For Fiat 124, 850 (All Versions and Years)
- Pre-cut, non-shaped pieces, 10% Larger in size, capable of covering all rear windows


APPLICATION:

- In addition to the film for the application you will need: Spatula, Cutter, Water and Fabric Softener, Nebulizer, Hairdryer or Heat Gun.
- The film must always be applied internally to the glass, however the external part is also necessary, which is fundamental for shaping and modeling the film before the final application on the internal part.

- Cut the film with a good margin compared to the size of the glass to be darkened (3-5cm).
- Thoroughly clean the glass internally and externally 2-3 times.
- Spray the mixture of water and softener mixed in a ratio of 1:10 on the outside of the glass.
- Apply the Film Externally to the Glass, Keeping the adhesive part of the Film facing towards you.
- Imprint the Film on the External Glass with the Spatula Forming a Large H.
- Shape the Film Using a Hairdryer and Spatula. The objective is to remove all the bubbles by making the Film adhere perfectly to the External Glass.
(the better it is processed now the easier it will be to move and apply the film internally later)
- Once the film is completely adhered without bubbles, shape it with the cutter by cutting off the excess, remaining within the margin of 2-3mm from the edge of the glass.
- Still leaving the film on the outside of the glass, make sure again that the inside of the glass is clean and proceed to spray the solution of water and softener inside the glass.
- Remove the protective film on the adhesive area of the film. Help yourself to remove it by spraying more water and fabric softener.
- Move the film to the inside of the glass, this time with the adhesive part facing the glass itself.
- Shape and flatten the film with the spatula, removing bubbles and liquid. (if the hairdryer has been used previously it will not be needed now)

- The glasses are operational after 24 hours
- Final adhesion is achieved after approximately 15 - 20 days at 18° C and in dry climate conditions.


MAINTENANCE AND CLEANING
Use high-quality cleaners specifically for glass surfaces. The cleaning system (cloth, sponge, etc.) must be wet and not abrasive with a pH value between 6 and 8 (neither too acidic nor too alkaline).


Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY:

ATTENTION: in Italy application is only permitted on rear windows and rear windshields. We invite you to check the individual regulations of each state.

- For Fiat 124, 850 (All Versions and Years)
- Pre-cut, non-shaped pieces, 10% Larger in size, capable of covering all rear windows


APPLICATION:

- In addition to the film for the application you will need: Spatula, Cutter, Water and Fabric Softener, Nebulizer, Hairdryer or Heat Gun.
- The film must always be applied internally to the glass, however the external part is also necessary, which is fundamental for shaping and modeling the film before the final application on the internal part.

- Cut the film with a good margin compared to the size of the glass to be darkened (3-5cm).
- Thoroughly clean the glass internally and externally 2-3 times.
- Spray the mixture of water and softener mixed in a ratio of 1:10 on the outside of the glass.
- Apply the Film Externally to the Glass, Keeping the adhesive part of the Film facing towards you.
- Imprint the Film on the External Glass with the Spatula Forming a Large H.
- Shape the Film Using a Hairdryer and Spatula. The objective is to remove all the bubbles by making the Film adhere perfectly to the External Glass.
(the better it is processed now the easier it will be to move and apply the film internally later)
- Once the film is completely adhered without bubbles, shape it with the cutter by cutting off the excess, remaining within the margin of 2-3mm from the edge of the glass.
- Still leaving the film on the outside of the glass, make sure again that the inside of the glass is clean and proceed to spray the solution of water and softener inside the glass.
- Remove the protective film on the adhesive area of the film. Help yourself to remove it by spraying more water and fabric softener.
- Move the film to the inside of the glass, this time with the adhesive part facing the glass itself.
- Shape and flatten the film with the spatula, removing bubbles and liquid. (if the hairdryer has been used previously it will not be needed now)

- The glasses are operational after 24 hours
- Final adhesion is achieved after approximately 15 - 20 days at 18° C and in dry climate conditions.


MAINTENANCE AND CLEANING
Use high-quality cleaners specifically for glass surfaces. The cleaning system (cloth, sponge, etc.) must be wet and not abrasive with a pH value between 6 and 8 (neither too acidic nor too alkaline).


Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY:

ATTENTION: in Italy application is only permitted on rear windows and rear windshields. We invite you to check the individual regulations of each state.

- For Fiat 124, 850 (All Versions and Years)
- Pre-cut, non-shaped pieces, 10% Larger in size, capable of covering all rear windows


APPLICATION:

- In addition to the film for the application you will need: Spatula, Cutter, Water and Fabric Softener, Nebulizer, Hairdryer or Heat Gun.
- The film must always be applied internally to the glass, however the external part is also necessary, which is fundamental for shaping and modeling the film before the final application on the internal part.

- Cut the film with a good margin compared to the size of the glass to be darkened (3-5cm).
- Thoroughly clean the glass internally and externally 2-3 times.
- Spray the mixture of water and softener mixed in a ratio of 1:10 on the outside of the glass.
- Apply the Film Externally to the Glass, Keeping the adhesive part of the Film facing towards you.
- Imprint the Film on the External Glass with the Spatula Forming a Large H.
- Shape the Film Using a Hairdryer and Spatula. The objective is to remove all the bubbles by making the Film adhere perfectly to the External Glass.
(the better it is processed now the easier it will be to move and apply the film internally later)
- Once the film is completely adhered without bubbles, shape it with the cutter by cutting off the excess, remaining within the margin of 2-3mm from the edge of the glass.
- Still leaving the film on the outside of the glass, make sure again that the inside of the glass is clean and proceed to spray the solution of water and softener inside the glass.
- Remove the protective film on the adhesive area of the film. Help yourself to remove it by spraying more water and fabric softener.
- Move the film to the inside of the glass, this time with the adhesive part facing the glass itself.
- Shape and flatten the film with the spatula, removing bubbles and liquid. (if the hairdryer has been used previously it will not be needed now)

- The glasses are operational after 24 hours
- Final adhesion is achieved after approximately 15 - 20 days at 18° C and in dry climate conditions.


MAINTENANCE AND CLEANING
Use high-quality cleaners specifically for glass surfaces. The cleaning system (cloth, sponge, etc.) must be wet and not abrasive with a pH value between 6 and 8 (neither too acidic nor too alkaline).


Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY:

- Specific for Fiat 124 - 850


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Specific for Fiat 124 - 850


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.