Cherokee KL (13-19)

Jeep Cherokee KL 13-19 | Tuning Accessories and LED Lights | QSPCARS

Active Filters

  • Color: 6.500K Ice White Light
  • Color: Anodized Red
  • Color: Anodized Steel
  • Color: Chromed

There Are 5 Products.

Sort by:
Sales, highest to lowest Relevance Name, A to Z Name, Z to A Price, low to high Price, high to low Reference, A to Z Reference, Z to A
HIR2-HIR LED Kit for JEEP CHEROKEE KL | LED Conversion Low + High Beam | CANbus 6500K 8000LM
  • -4%
Add to Wishlist
HIR2-HIR LED Kit for JEEP CHEROKEE KL | LED Conversion Low +...
COMPATIBILITY:

- JEEP CHEROKEE KL (from 2013) with BI-HALOGEN PROJECTOR HEADLIGHTS, Low + High Beam



FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.
Add to Wishlist
€61.89 Regular Price €64.47
License Plate LED Canbus for Jeep Cherokee KL | 18 Leds 6.500k White Ice, Plug & Play
  • -2%
Add to Wishlist
License Plate LED Canbus for Jeep Cherokee KL | 18 Leds 6.500k...
COMPATIBILITY:

- Jeep Cherokee (KL) 2013>

INSTRUCTION:

- Remove the current led plates, using a screwdriver if necessary, inserting the tip in the side part of the plate and apply pressure towards the outside: the plate will come out./ If Screws present Remove them by unscrewing them to release the plate

- Disconnect the cable and disconnect definitely the plate.

- Connect the new LED PLATE to the cable and replace it inside the housing. Repeat the same operation with the second plate.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES
Add to Wishlist
€22.29 Regular Price €22.74
Rear Car Chrome License Plate Support Kit for Jeep, in Stainless Steel
Add to Wishlist
Rear Car Chrome License Plate Support Kit for Jeep, in...
COMPATIBILITY:

- For JEEP Cars

It is applicable on any vehicle with an Indentation on the bumper where it will be possible to fix the bracket (LOOK AT THE PHOTO).



ASSEMBLY:

- Put the plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the Screws

- Remove the plate and apply it on the new plate holder

- Apply the chromed frame and Fix it with the 4 screws supplied




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

Add to Wishlist
€19.78
Front LICENSE PLATE Holder for Jeep Bracket SIDE RELOCATOR In Anodized STEEL tuning
  • -1%
Add to Wishlist
Front LICENSE PLATE Holder for Jeep Bracket SIDE RELOCATOR In...
COMPATIBILITY:

- For JEEP Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

Add to Wishlist
€19.06 Regular Price €19.25
Front License Plate Holder for Jeep, Side Relocator Bracket, in Anodized Red Steel
  • -1%
Add to Wishlist
Front License Plate Holder for Jeep, Side Relocator Bracket,...
COMPATIBILITY:

- For JEEP Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

Add to Wishlist
€19.06 Regular Price €19.25