Compass II (17-21)

Jeep Compass 2 17-21 | Tuning Accessories and LED Lights | QSPCARS

Active Filters

  • Color: Anodized Red
  • Color: Anodized Steel
  • Color: Matt Black
  • Color: Metallic Grey
Car BOOSTER Emergency JUMP STARTER Portable in your Jeep + POWER BANK for Planes
  • -5%
  • Out of Stock
Car BOOSTER Emergency JUMP STARTER Portable in your Jeep +...
COMPATIBILITY

Jump Starter Mode (Emergency Start-up):

- Cars (including Jeep), Motorcycles, Pic ups, Suvs, Commercial Vehicles and Boats
- Petrol, Diesel, Hybrid, Start and Stop Engines
- Petrol Engines up to 8.000cc Displacement, Diesel Engines up to 7.000cc Displacement

Power Bank Mode (Portable Charger):

- Any 12V electrical or electronic accessory or appliance, including Apple devices


JUMP STARTER USE:

- Access the Battery Compartment of your Jeep (or of the Motorcycle or Watercraft)
- Connect the Wiring Harness that has the two Pliers (Red and Black) at one end, and the Blue Plug at the other, to the Jump Starter
- Switch on the Jump Stater By pressing the only available button, to check the charge status
- Connect the Red Pliers to the Positive Pole, the Black Pliers to the Negative Pole (NO FEAR, if you make a mistake there will be NO sparks)
- After the connection, press the only button on the transformer of the Harness, if connected correctly a green light will turn on; if it is red, invert the polarity or check the clamp connection and press the button again
- A green light proceed with starting the vehicle

POWERBANK USE:

- Connect the cable needed to power the device you want to charge to a USB or USB-C socket and press the power button
- Wireless recharge, place a device designed for this recharge on the lightning bolt design on the Power Bank and press the power button
- The recharge or flow of current through the cigarette lighter takes place by connecting the DC plug, which has the cigarette lighter input at the end; Therefore insert the cigarette lighter socket and press the ignition button




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES
€150.10 Regular Price €158.00
ERROR FREE Canceller Anti-Flicker Decoder Low Beams JEEP...
COMPATIBILITY:

FULL LED H11 KIT

- Jeep Compass 2 (2017-2021)


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- CHECK: Connect only the Sockets (PLUG AND PLAY); if there are no problems, proceed with the assembly

- CONNECT MALE SOCKET: Connect the male socket to the CAR

- CONNECT FEMALE SOCKET: Connect the Full Led Kit to the Female Socket

- CHECK: Start the vehicle to check if there are no problems, only then proceed to lock the LED bulb.

- INSTALLATION: Repeat the operation on the second headlight

It is PREFERABLE to keep the resistors out of the headlight, since the lower the overheating is, the longer the DURATION OF YOUR LED KIT WILL BE.



NON-STANDARD CASES

- DEEPER DUST CAPS:
Mounting a TRANSFORMATION kit, and not simple spare bulbs, it has bigger dimensions. If the installation of the kit does not allow the closure of the lighthouse, visit our store for the DEEPER DUST CAPS.





We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.
€32.28 Regular Price €33.98
Front LICENSE PLATE Holder for Jeep Bracket SIDE RELOCATOR In...
COMPATIBILITY:

- For JEEP Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€19.06 Regular Price €19.25
Front License Plate Holder for Jeep, Side Relocator Bracket,...
COMPATIBILITY:

- For JEEP Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€19.06 Regular Price €19.25