Left Banner

  • LeftBanner 1

Cee'd - Pro Cee' d II JD (12-18)

Kia Cee'd 2 JD | Tuning Accessories and Xenon LED Lights | QSPCARS

Active Filters

  • Color: Anodized Red
  • Color: Anodized Steel
  • Color: Metallic Grey
  • Color: Satin Black

There Are 5 Products.

Car BOOSTER Emergency JUMP STARTER Portable in your Kia + POWER BANK for Planes
  • -5%
  • Out of Stock
Car BOOSTER Emergency JUMP STARTER Portable in your Kia +...
COMPATIBILITY

Jump Starter Mode (Emergency Start-up):

- Cars (including Kia), Motorcycles, Pic ups, Suvs, Commercial Vehicles and Boats
- Petrol, Diesel, Hybrid, Start and Stop Engines
- Petrol Engines up to 8.000cc Displacement, Diesel Engines up to 7.000cc Displacement

Power Bank Mode (Portable Charger):

- Any 12V electrical or electronic accessory or appliance, including Apple devices


JUMP STARTER USE:

- Access the Battery Compartment of your Kia (or of the Motorcycle or Watercraft)
- Connect the Wiring Harness that has the two Pliers (Red and Black) at one end, and the Blue Plug at the other, to the Jump Starter
- Switch on the Jump Stater By pressing the only available button, to check the charge status
- Connect the Red Pliers to the Positive Pole, the Black Pliers to the Negative Pole (NO FEAR, if you make a mistake there will be NO sparks)
- After the connection, press the only button on the transformer of the Harness, if connected correctly a green light will turn on; if it is red, invert the polarity or check the clamp connection and press the button again
- A green light proceed with starting the vehicle

POWERBANK USE:

- Connect the cable needed to power the device you want to charge to a USB or USB-C socket and press the power button
- Wireless recharge, place a device designed for this recharge on the lightning bolt design on the Power Bank and press the power button
- The recharge or flow of current through the cigarette lighter takes place by connecting the DC plug, which has the cigarette lighter input at the end; Therefore insert the cigarette lighter socket and press the ignition button




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES
€150.10 Regular Price €158.00
Car Roof Rack Bars for Kia Ceed 2 Wagon ORIGINAL Nordrive Evos...
COMPATIBILITY:

- Kia Ceed 2 JD Sportswagon (2012-2018), with Flush Railings (Low Railings)


INSTALLATION:

- For a Perfect Installation Mount the Bars at Approximately 70cm Distance Between Them.
- For Perfect Soundproofing Mount the Bars in the rearmost possible area of the Vehicle.
- For Perfect Positioning and Centering during Assembly, consult the graduated scale on the bottom of the Bars.

- Mount the roof bars as per the instructions
- Position them on the roof with the pointed part facing backwards
- Open the locks with the key provided
- Unscrew the pin that allows the clamp to open to the maximum allowed
- Position the bars on the low rails centering them on the roof
- Tighten the pin that closes the clamp to the maximum allowed (max 6Nm)
- Close the locks and plug the remaining empty channels with the gaskets provided


ATTENTION it is good practice to carry out a control pit stop after the first 100km, then after 250km and finally after 500km.


Although simple and intuitive, FOR OPTIMAL INSTALLATION, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility for the item mounted and subsequently detached.
We trust in your common sense.
€150.08 Regular Price €157.98
Front LICENSE PLATE Holder for Kia Bracket SIDE RELOCATOR In...
COMPATIBILITY:

- For KIA Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€19.06 Regular Price €19.25
Front License Plate Holder for Kia, Side Relocator Bracket, in...
COMPATIBILITY:

- For KIA Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€19.06 Regular Price €19.25