For Audi

COMPATIBILITY:

- For AUDI R8 (42) Facelift, 2013-2015

- Compatible with Versions: Coupe, Spyder

** Attention! NOT COMPATIBLE with Pre-Facelift Version**



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI Q5 (FY) S-Line, SQ5 Pre-Facelift, 2016-2020

** Attention! ONLY FOR S-LINE BUMPERS, NO RSQ5 and Vehicles with Front Camera **


INSTRUCTIONS:

- Just Replace the current ones as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI Q5 (FY) Pre-Facelift, 2016-2020

** Attention! NOT COMPATIBLE with S-Line, RSQ5 Versions and Vehicles with Front Camera **


INSTRUCTIONS:

- Just Replace the current ones as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI TT FV (8S) Pre-Facelift, 2014-2018
- For AUDI TT FV S-LINE (8S) Pre-Facelift, 2014-2018

- Compatible with Versions: Coupe, Roadster

** Attention! NOT COMPATIBLE with RSTT**



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI A5 F5 (8W6) Facelift, from 2020
- For AUDI S5 F5 (8W6) Facelift, from 2020

- Also compatible with all versions: Coupe, Convertible, Sporback

** Attention! NOT COMPATIBLE with RS5 version**


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI Q3 (F3), from 2018
- For AUDI SQ3 (F3), from 2018

** Attention! NOT COMPATIBLE with RSQ3 version**



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI Q2 (GA) Facelift, from 2020
- For AUDI SQ2 (GA) Facelift, from 2020


** Attention! NOT COMPATIBLE with RSQ2**



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI A6 C7 Pre-Facelift (2011>2014)



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI Q3 8U Pre-Facelift (2011>2014)



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI Q5 (FY) Pre-Facelift, 2016-2020
- For AUDI SQ5 (FY) Pre-Facelift, 2016-2020

** NOT COMPATIBLE with RSQ5 and Vehicles with Front Camera**


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI Q3 (8U) Facelift, 2014-2018
- For AUDI SQ3 (8U) Facelift, 2014-2018
- For AUDI RSQ3 (8U) Facelift, 2014-2018



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI A3 (8Y), from 2020
- For AUDI S3 (8Y), from 2020

- Grille also compatible with the Sedan versions

** Attention! NOT COMPATIBLE with RS3 version**


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI Q5 (8R) Pre-Facelift, 2008-2012
- For AUDI SQ5 (8R) Pre-Facelift, 2008-2012 - Attention Required Modification for Installation (see photo 4)


** NOT COMPATIBLE with RSQ5 and Vehicles with Front Camera**



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI A1 8X (2010-2014)

** If Facelift from 2015, search our store for the correct item **



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI Q2 (GA) Pre-Facelift, 2016-2020
- For AUDI SQ2 (GA) Pre-Facelift, 2016-2020


** Attention! NOT COMPATIBLE with RSQ2**



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI A5 (8T) S-Line, S5 Pre-Facelift, 2007-2011

- Compatible with all Versions: Coupé, Cabriolet, Sportback

** Attention! ONLY FOR S-LINE BUMPERS, NO RS5**



INSTRUCTIONS:

- Just Replace the current ones as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI A5 (8T) Pre-Facelift, 2007-2011

- Compatible with all Versions: Coupé, Cabriolet, Sportback

** Attention! NOT COMPATIBLE with S-Line, RS5 Version**



INSTRUCTIONS:

- Just Replace the current ones as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI A1 8X Facelift (from 2015)

** If Pre-Facelift, search our store for the correct item **



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI A6 (C7) Facelift, 2014-2018
- For AUDI S6 (C7) Facelift, 2014-2018

- Compatible with Versions: Avant, Limousine

** Attention! NOT COMPATIBLE with RS6, Allroad version and Vehicles with Front Camera**


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For AUDI Q3 8U Pre-Facelift (2011>2014)



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI A3 8V Facelift (from 2016)



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI A3 8V (2012>2016)


INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI A3 8V (2012>2016), "WITH S-LINE VERSION BUMPER"



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For AUDI A6 C7 Pre-Facelift (2011>2014)



INSTRUCTIONS:

- Just Replace the current one as a perfect replacement: 100% TESTED COMPATIBILITY



FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.