LED DRL Daytime Running Lights & Stop

Hyundai with Daytime Running Lights in Headlight

DRL DAYTIME LIGHTS & LED BRAKE LIGHTS


Renew the Look of Your Car by Adding LED DRL Strips or LED Brake Lights.

DRL Lights (Day Running Light) or Daytime Running Lights Improve the Visibility of the Vehicle Giving a More Current Look in Line with Innovation.

QSPCARS LED Accessories Are Never Invasive, Our Task Is to Modify the Lights While Preserving the Original Component.

Car Approved LED Daytime Running Lights DRL Universal | QSPCARS

Active Filters

Universal DRL LED Round Fog Lights APPROVED with Powerful White LED Daytime Running Lights
  • -2%
  • New
  • Out of Stock
Universal DRL LED Round Fog Lights APPROVED with Powerful...
COMPATIBILITY

- Vehicles 8-32V (CAR, TRUCK) with 3.5 Inch (90MM) round headlights
- Distance Between Fixing Holes (4 Holes): Width: 100mm - Height: 50m


ASSEMBLY INSTRUCTIONS:

1) Remove the old Fog Lights, and disconnect them, or create the accommodation for the new Fog Lights
2) Connect the supplied cables to the fog light, as explained in point 3:
3) Connect the control unit to the fog light using the round 4-pin plug (remember, the wiring diagram is shown on the control units)
FROM THE CONTROL UNIT THERE IS A DIRECTION OF TWO CABLES, respectively:
- a cable H8 - H11 - H9 - H16, which will be connected to the car power supply (This socket also acts as a Negative Pole, in fact, if not connected, the DRLs will not turn on)
- a double color cable (yellow-red), to which it will be necessary to connect the yellow-red extension cable, also supplied (this cable will be the power supply of the DRL lights)
4) Connect the Red Cable to the positive pole of the Battery
5) Connect the Yellow Cable to the negative pole of the battery, or to the negative pole of the headlights
6) Connect the second fog light to the second control unit, as already done for the first fog light
7) In this case, at the branch of the double cable of the control unit, the yellow-red cable must be connected in a chain to the wiring of the first spot, using the plug, on the yellow-red cable


FOR OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT


- the fixture has a socket H8 - H11 - H9 - H16> 9005 - HB3 - H10> 9006 - HB4, therefore in most cases it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule will apply (connection only)

On some cars, it may be necessary to make small changes during installation. We always trust in your common sense.



We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES
€189.26 Regular Price €193.12
2 Universal LED DRL Daytime Running Light for Cars 29CM |...
COMPATIBILITY:

Universal, 12-24v Vehicles


INSTRUCTIONS:

Possibility of Mounting on Bumper, Hood, Fog Lamp Grills (or wherever it is possible to fix the brackets)

- Install the brackets in the desired position, and fix them using screws / bolts (not included)

- Place the DRL plates on the special brackets, and fix them using 2 screws (not included)

- Connect Black Wire to Ground (Battery Negative Pole)

- Connect the red wire to the position lights or under key




FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

We do not take responsibility for: incorrect purchases-violations of regulations or laws of any state-damages, which you could cause to yourself, to third parties or to the same article. as we describe every single specification in detail.

€111.47 Regular Price €114.92
LED Fog Lights 4" Universal APPROVED, with LED DRL Daytime Running Lights | White Light 6500K
  • -2%
  • New
  • Out of Stock
LED Fog Lights 4" Universal APPROVED, with LED DRL Daytime...
COMPATIBILITY:

- Jeep Wrangler JK (2007-2018)
- Jeep Wrangler TJ (1997-2007)
- Jeep Wrangler JL (from 2018)
- Jeep Grand Cherokee (2011-2013)
- Jeep Cherokee KL (2013-2019)
- Dodge Journey (2008-2010)
- Dodge Magnum (2004-2008)
- Dodge Charger IV (2011-2014)
- Chrysler PT Cruiser Facelift (2006-2010)
- Chrysler 300 (2004-2011) - Touring version or Limited Models ONLY
- Fiat Freemont (2011-2018)
- Hummer H1 (1992-2006)
- Hummer H2 (2003-2009)


- 9-12V Vehicles with 4 Inches (98MM) Round Fog Lights
- Distance between fixing holes (4 holes): Width: 100,4mm - Height: 60m


ASSEMBLY INSTRUCTIONS: we always recommend installation by an EXPERT

1) Remove the old fog lights and disconnect them
2) On the new LED fog lights there are 2 cables respectively:
- H8 - H11- H9 - H16 socket for Plug & Play connection to the vehicle (fog light power supply)
- Yellow cable to connect to any vehicle light power supply (DRL light power supply)
3) Align the 4 holes by bolting the fog light body into the housing


For vehicles that do not have an H8 -H9-H11-H16 socket:

An adapter cable is supplied to connect to the socket of the new LED fog lights, this wiring ends with a positive wire (red) and a negative wire (black) which will be connected to the power supply of the old fog lights.



We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES
€107.78 Regular Price €109.98
2 Universal LED DRL Daytime Running Light for Cars 18CM |...
COMPATIBILITY:

Universal, 12-24v Vehicles


INSTRUCTIONS:

Possibility of Mounting on Bumper, Hood, Fog Lamp Grills (or wherever it is possible to fix the brackets)

- Install the brackets in the desired position, and fix them using screws / bolts (not included)

- Place the DRL plates on the special brackets, and fix them using 2 screws (not included)

- Connect Black Wire to Ground (Battery Negative Pole)

- Connect the red wire to the position lights or under key




FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

We do not take responsibility for: incorrect purchases-violations of regulations or laws of any state-damages, which you could cause to yourself, to third parties or to the same article. as we describe every single specification in detail.

€100.72 Regular Price €104.92
Car Universal Adhesive Rear LED SPOILER | Trunk Roof Led Lip...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€53.17 Regular Price €55.97
Car Universal Adhesive Rear LED SPOILER | Trunk Roof Led Lip 100Cm in Black CARBON Fiber Effect
  • -5%
  • New
  • Out of Stock
Car Universal Adhesive Rear LED SPOILER | Trunk Roof Led Lip...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€53.17 Regular Price €55.97
Car Universal Adhesive Rear LED SPOILER | Trunk Roof Led Lip...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€53.17 Regular Price €55.97
Car Universal Adhesive Rear LED SPOILER | Trunk Roof Led Lip...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€53.17 Regular Price €55.97
Car Universal Adhesive Rear LED SPOILER | Trunk Roof Led Lip...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€53.17 Regular Price €55.97
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof Led Lip 94Cm
  • -5%
  • New
  • Out of Stock
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€47.47 Regular Price €49.97
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof Led Lip 100Cm
  • -5%
  • New
  • Out of Stock
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€47.47 Regular Price €49.97
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof Led Lip 110Cm
  • -5%
  • New
  • Out of Stock
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€47.47 Regular Price €49.97
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof Led Lip 120Cm
  • -5%
  • New
  • Out of Stock
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€47.47 Regular Price €49.97
Universal Car Rear LED SPOILER, Black | Adhesive Trunk Roof...
COMPATIBILITY:

- UNIVERSAL

It is applicable on any vehicle: Cars, SUVs, Perfect adaptability.


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€47.47 Regular Price €49.97
2 Flexible LED Strips DRL, Daytime Running Light + Sequential...
COMPATIBILITY:

Universal, Suitable for Cars and Motorcycles


INSTRUCTIONS:

You can install them on headlights, bumpers, hood, fog lights

- Carefully clean by removing the Surface where to install the LED Strip from any Impurities.

- Connect Black Wire to Earth (Battery Negative Pole)

- Connect the red wire to the parking lights or under the key

- Connect the yellow wire to the positive pole of the Turn Signal

- Check the required length, proceed to cut the excess strip** at the points indicated on the back of the LED strip.

- Remove Adhesive Protective Film and adhere LED Strip on the Desired Point
(Taking care that the surface is completely dry and free of all impurities)

- Heat everything with a thermal hairdryer at a suitable distance to make the adhesive adhere perfectly (cold months).

DO NOT wash or rinse for 72H

** If possible, avoid cutting the band, as although prepared, unfortunately the warranty will expire after the modification **


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

We do not take responsibility for: incorrect purchases-violations of regulations or laws of any state-damages, which you could cause to yourself, to third parties or to the same article. as we describe every single specification in detail.

€36.85 Regular Price €37.99
2 Flexible LED Strips DRL, Daytime Running Light + Sequential...
COMPATIBILITY:

Universal, Suitable for Cars and Motorcycles


INSTRUCTIONS:

You can install them on headlights, bumpers, hood, fog lights

- Carefully clean by removing the Surface where to install the LED Strip from any Impurities.

- Connect Black Wire to Earth (Battery Negative Pole)

- Connect the red wire to the parking lights or under the key

- Connect the yellow wire to the positive pole of the Turn Signal

- Check the required length, proceed to cut the excess strip** at the points indicated on the back of the LED strip.

- Remove Adhesive Protective Film and adhere LED Strip on the Desired Point
(Taking care that the surface is completely dry and free of all impurities)

- Heat everything with a thermal hairdryer at a suitable distance to make the adhesive adhere perfectly (cold months).

DO NOT wash or rinse for 72H

** If possible, avoid cutting the band, as although prepared, unfortunately the warranty will expire after the modification **


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

We do not take responsibility for: incorrect purchases-violations of regulations or laws of any state-damages, which you could cause to yourself, to third parties or to the same article. as we describe every single specification in detail.

€34.91 Regular Price €35.99