Golf VII (12-17)

COMPATIBILITY:

- It Can be Installed on Volkswagen Golf, with Roof Bars (already installed), with a Minimum Load Capacity of 90kg


- IF ROOF BARS HAVE A CAPACITY OF 90KG, CAN THEY SUPPORT THE TENT, WHICH WEIGHS 90KG + THE WEIGHT OF THE PEOPLE WHO WILL HOST IT?

The maximum weight capacity supplied when purchasing a pair of roof bars always represents the dynamic capacity of the bars, i.e. the maximum capacity of the same when the vehicle is moving, but all the bars, in addition to having a dynamic capacity, have a static capacity, which in most cases it is not reported on the bars.

The Static Capacity Represents the Maximum Weight Capacity of the Roof Bars with the Vehicle Stationary, and on average the latter Reaches Approximately X3 Times the Dynamic Capacity.


- CAN ALL CARS HOLD A ROOF TENT?

Absolutely Yes. The side members of each car are designed to support more than the weight of the car itself, since, in the event of an accident and the car overturning, for safety reasons, it must support its own weight.

Since the smallest of the cars weighs at least 1 Ton, by logic, it is obvious that any car (even the smallest!) can hold both the roof tent and its guests inside, without any problem.


ASSEMBLY:

- Place the tent on the roof bars of your vehicle (2 people min.)
- Under the tent there are 2 channels, insert 4 steel inserts crossed by the bolt for each channel
- Scrolling through the inserts equipped with bolts, match 2 bolts, one with the outside and one with the inside of the roof rack
- Mount the bracket supplied by gripping the part underneath the roof rack and tighten the bolts
- Remember to Tighten the Bolts Whenever You Travel.


OPENING:

- Press on the Steel Jack Closure Buckles that block the Closure Laces
- Accompany the automated opening upwards
- USEFUL ADVICE: We recommend leaving the door and window zips open for quick and easy opening and closing of the tent
- The closure occurs through long laces designed for draft from the ground



Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY

- FOR Volkswagen Golf 7 MK7 (2010-2017), with Halogen Headlights

** ATTENTION: H7 Low Beam Bulbs NOT INCLUDED **


Check that the socket shown in the picture is like yours, vice versa it is necessary to get an adapter that modifies the socket, (which we do not own).


FOR OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT


- The fixture has the same connections as the original, therefore it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (connection only) will apply.






We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY:

- Volkswagen Golf 7 (2012-2017), with Steering Wheel as per Photo No. 2
**For Versions WITH AND WITHOUT STEERING WHEEL PADDLE SHIFT EXTENSION**


ASSEMBLY: Operation that requires the use of Professional Equipment and Knowledge.

- Disassembly of your original steering wheel and removal of central air bag including logo and any steering wheel or paddle controls.
- Assembly of the Sports Steering Wheel in the Same Position.
- Fit the Central Cover and Airbag previously removed from your original steering wheel onto the sports steering wheel.
- Mount any paddles or steering wheel controls previously removed from your original steering wheel onto the sports steering wheel.



(Although simple and intuitive, we always recommend assembly by an expert in the sector, to avoid possible damage to things or people. DO IT YOURSELF IS NOT RECOMMENDED)

WE DO NOT ASSUME RESPONSIBILITY FOR DAMAGES THAT YOU MAY CAUSE TO THE PRODUCT, PEOPLE, THINGS, OR THE CAR ITSELF, BY DO-IT-YOURSELF ASSEMBLY, OR BY BREACH OF THE LAWS OF EACH SINGLE COUNTRY, AS WE DESCRIBE EVERY SINGLE SPECIFICATION IN DETAIL.

We trust in your common sense.

COMPATIBILITY

VOLKSWAGEN cars:

- with wheels between 14 inches and 23 inches
- with wheels of max diameter 750 mm
- Max weight 2,700 kg


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY

- FOR Volkswagen Golf 7 MK7 (2012-2017)
- FOR Volkswagen Golf 7 MK7 Facelift (2017-2019)

- Not suitable for VW Golf VI Station Wagon (Variant, SportsVan, Estate, R Wagon, SportWagen, Alltrack)
- Not suitable for VW Golf VI with Original Equipment LED taillights
- Not suitable for RHD Models


FOR OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT


- The fixture has the same connections as the original, therefore it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule (connection only) will apply.






We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY

VOLKSWAGEN cars:

- with wheels between 14 inches and 23 inches
- with wheels of max diameter 750 mm
- Max weight 2,700 kg


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY:

- For VOLKSWAGEN GOLF, with Roof Bars already Installed



ASSEMBLY:

1) Join together the two parcels that make up the Luggage Rack
2) Screw them together using the appropriate screws
3) Secure the Luggage Carrier to the Roof Bars, using the 4x Brackets + Rubber Shims supplied




Although mouting is simple and intuitive, FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT.
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- SPECIFIC for VOLKSWAGEN GOLF 7 (2012-2019) " ONLY With the Interior as per "PHOTO 2"

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY

VOLKSWAGEN cars:

- with wheels between 14 inches and 23 inches
- with wheels of max diameter 750 mm
- Max weight 2,700 kg


APPLICATION: SEE THE VIDEO TUTORIAL By scanning QR CODE in Listing Images

- Place Easyrise in front of each wheel.
- Press on the gelpads to make them adhere correctly to the ground (if they do not adhere correctly, clean the gelpads with a degreaser and water).
- Perform a brief reverse motion to facilitate climbing onto the cushion.
- Climb onto the cushion with inertia without accelerating on the ramp.



We do not assume responsibility for: incorrect purchases - violations of regulations or laws of each state - damage that could be caused to you, to third parties, to the Vehicle or to the item itself, as we describe every single specification in detail.

We trust in your common sense.

COMPATIBILITY:

VOLKSWAGEN GOLF VII : Hatchback / Variant (5G,BE1,BA5)

- Volkswagen Golf VII 1.0 TSI (63 KW / 86 CV) (01.2017 - 12.2018)
- Volkswagen Golf VII 1.0 TSI (81 KW / 110 CV) (11.2016 - 12.2018)
- Volkswagen Golf VII 1.0 TSI (85 KW / 115 CV) (05.2015 - 12.2018)
- Volkswagen Golf VII 1.2 TSI (63 KW / 86 CV) (08.2012 - 12.2018)
- Volkswagen Golf VII 1.2 TSI (77 KW / 105 CV) (11.2012 - 12.2018)
- Volkswagen Golf VII 1.2 TSI (81 KW / 110 CV) (04.2014 - 12.2018)
- Volkswagen Golf VII 1.4 TSI (103 KW / 140 CV) (08.2012 - 12.2018)
- Volkswagen Golf VII 1.4 TSI (110 KW / 150 CV) (05.2014 - 12.2018)
- Volkswagen Golf VII 1.4 TSI (90 KW / 122 CV) (11.2012 - 12.2018)
- Volkswagen Golf VII 1.4 TSI (92 KW / 125 CV) (05.2014 - 12.2018)
- Volkswagen Golf VII 1.6 (81 KW / 110 CV) (05.2014 - 12.2018)
- Volkswagen Golf VII 1.4 GTE Hybrid (110 KW / 150 CV) (05.2014 - 12.2018)
- Volkswagen Golf VII 1.4 TSI MultiFuel (90 KW / 122 CV) (04.2013 - 12.2018)
- Volkswagen Golf VII 1.4 TSI MultiFuel (92 KW / 125 CV) (12.2013 - 12.2018)
- Volkswagen Golf VII 1.4 TGI CNG (81 KW / 110 CV) (06.2013 - 12.2018)



Engine initials : CZEA, CWLA, CHPB, CPTA, CJZA, CYVB, CUKB, CXUA, CMBA, CXSA, CXSB, CPWA, CZCA


MOUNTING:

- Necessarily to be done by a professional in the field




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted .
We trust in your common sense.

COMPATIBILITY:

VOLKSWAGEN GOLF SPORTSVAN : (AM1)

- Volkswagen Golf Sportsvan 1.0 TSI (85 KW / 115 CV) (05.2015 - 12.2018)
- Volkswagen Golf Sportsvan 1.2 TSI (63 KW / 86 CV) (05.2014 - 12.2018)
- Volkswagen Golf Sportsvan 1.2 TSI (81 KW / 110 CV) (04.2014 - 12.2018)
- Volkswagen Golf Sportsvan 1.4 TSI (110 KW / 150 CV) (02.2014 - 12.2018)
- Volkswagen Golf Sportsvan 1.4 TSI (92 KW / 125 CV) (04.2014 - 12.2018)
- Volkswagen Golf Sportsvan 1.6 (81 KW / 110 CV) (05.2014 - 12.2018)
- Volkswagen Golf Sportsvan 1.4 TSI MultiFuel (92 KW / 125 CV) (04.2014 - 12.2018)



Engine initials : CZEA, CWLA, CHPB, CPTA, CJZA, CYVB, CUKB, CXUA, CMBA, CXSA, CXSB, CPWA, CZCA


MOUNTING:

- Necessarily to be done by a professional in the field




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted .
We trust in your common sense.

COMPATIBILITY:

VOLKSWAGEN GOLF VII: Hatchback / Variant (5G,BE1,BA5)

- Volkswagen Golf VII 1.6 TDI (66 KW / 90 CV) (04.2013 - 12.2018)
- Volkswagen Golf VII 1.6 TDI (77 KW / 105 CV) (05.2013 - 12.2018)
- Volkswagen Golf VII 1.6 TDI (81 KW / 110 CV) (01.2013 - 12.2018)
- Volkswagen Golf VII 1.6 TDI (85 KW / 115 CV) (11.2016 - 12.2018)
- Volkswagen Golf 1.6 BlueMotion Technology (77 KW/ 105 CV) (2012 - 2018)
- Volkswagen Golf VII 1.6 TDI 4motion (77 KW / 105 CV) (05.2013 - 12.2018)
- Volkswagen Golf VII 1.6 TDI 4motion (81 KW / 110 CV) (01.2013 - 12.2018)
- Volkswagen Golf VII 2.0 GTD (135 KW / 184 CV) (04.2013 - 12.2018)
- Volkswagen Golf VII 2.0 TDI (105 KW / 143 CV) (08.2012 - 12.2018)
- Volkswagen Golf VII 2.0 TDI (110 KW / 150 CV) (11.2012 - 12.2018)
- Volkswagen Golf VII 2.0 TDI (81 KW / 110 CV) (05.2013 - 12.2018)
- Volkswagen Golf VII 2.0 TDI 4motion (110 KW / 150 CV) (11.2012 - 12.2018)



Engine Initials: CUSB, CXMA, CLHA, CRKB, CXXB, DBKA, CRBC, CRLB, CRUA, DEJA, CUNA, CRBD, CRLC, CRFA, CRFC, CUPA, DCYA, DDYA, DGCA, CNHA, CNHC, CSUA, CSUB, DETA, DFVA, DEUA, DEUB, DEUC, CSUE, CSUD, DFGA, DFHA, CLJA, CUVB, CUVC , CUVD, CUWA, CLLB, CYLA, DBBA, DFTA, DFTB, DFTC, DFUA, CRVA, CRVC, DFFA, CUSA, CUTA, CLHB, CXXA, CRMB, CKFC, CKFB, CUUB, DFSB, CUUA, DFSA, CUUD, DFSD, CUUE, CUUF, DFSC, DFSE, DFSF, CRKA, CYKB, DDYB, CRLD, DCYB, DEJB, CRGA, DCXA, DCZA, DFCA, DFEA, DDAA, CYZB, CYZA, CUVE, DGDB, DFGC, CRFD, CRGB, CYKC, DBGC, DGDA, DFEB, DFGB, CXGA, CXGB, CXHB, CXFA, CXHA, CXEB


MOUNTING:

- Necessarily to be done by a professional in the field




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted .
We trust in your common sense.

COMPATIBILITY:

VOLKSWAGEN GOLF SPORTSVAN: (AM1)

- Volkswagen Golf Sportsvan 1.6 (81 KW / 110 CV) (05.2014 - 12.2018)
- Volkswagen Golf Sportsvan 1.6 TDI (66 KW / 90 CV) (02.2014 - 12.2018)
- Volkswagen Golf Sportsvan 2.0 TDI (110 KW / 150 CV) (02.2014 - 12.2018)
- Volkswagen Golf Sportsvan 2.0 TDI (81 KW / 110 CV) (05.2014 - 12.2018)



Engine Initials: CUSB, CXMA, CLHA, CRKB, CXXB, DBKA, CRBC, CRLB, CRUA, DEJA, CUNA, CRBD, CRLC, CRFA, CRFC, CUPA, DCYA, DDYA, DGCA, CNHA, CNHC, CSUA, CSUB, DETA, DFVA, DEUA, DEUB, DEUC, CSUE, CSUD, DFGA, DFHA, CLJA, CUVB, CUVC , CUVD, CUWA, CLLB, CYLA, DBBA, DFTA, DFTB, DFTC, DFUA, CRVA, CRVC, DFFA, CUSA, CUTA, CLHB, CXXA, CRMB, CKFC, CKFB, CUUB, DFSB, CUUA, DFSA, CUUD, DFSD, CUUE, CUUF, DFSC, DFSE, DFSF, CRKA, CYKB, DDYB, CRLD, DCYB, DEJB, CRGA, DCXA, DCZA, DFCA, DFEA, DDAA, CYZB, CYZA, CUVE, DGDB, DFGC, CRFD, CRGB, CYKC, DBGC, DGDA, DFEB, DFGB, CXGA, CXGB, CXHB, CXFA, CXHA, CXEB


MOUNTING:

- Necessarily to be done by a professional in the field




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted .
We trust in your common sense.

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Volkswagen Golf

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

VOLKSWAGEN GOLF SPORTSVAN :

- Golf Sportsvan 03.11.2014 -> 1.6 TDI (90 PS)
- Golf Sportsvan 2014 -> 1.6 TDI (90 PS)
- Golf Sportsvan 03.11.2014 -> 1.6 TDI (110 PS)
- Golf Sportsvan 2014 -> 1.6 TDI (110 PS)
- Golf Sportsvan 2014 -> 1.6 TDI (115 PS)
- Golf Sportsvan 2014 -> 1.6 TDI (116 PS)


Engine Initials: CRKA,CXXA,DDYB,CXXB,DBKA,DDYA,DGTE



MOUNTING:

- Necessarily to be done by a professional in the field




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted .
We trust in your common sense.

COMPATIBILITY:

VOLKSWAGEN GOLF VII :

- Golf 7 (5G) 03.11.2014 -> 1.6 TDI (90 PS)
- Golf 7 (5G) 03.11.2014 -> 1.6 TDI (110 PS)
- Golf 7 (5G) 2013 - 2017 1.6 TDI (110 PS)
- Golf 7 (5G Facelift) 2017 -> 1.6 TDI (90 PS)
- Golf 7 (5G Facelift) 2017 -> 1.6 TDI (105 PS)
- Golf 7 (5G Facelift) 2017 -> 1.6 TDI (115 PS)
- Golf 7 (5G Facelift) 2017 -> 1.6 TDI (116 PS)



Engine Initials: CRKS,CXXA,CXXB,DBKA,DDYB,CLHA,DDYA,DGTE




MOUNTING:

- Necessarily to be done by a professional in the field




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted .
We trust in your common sense.

COMPATIBILITY

Jump Starter Mode (Emergency Start-up):

- Cars (including Volkswagen), Motorcycles, Pic ups, Suvs, Commercial Vehicles and Boats
- Petrol, Diesel, Hybrid, Start and Stop Engines
- Petrol Engines up to 8.000cc Displacement, Diesel Engines up to 7.000cc Displacement

Power Bank Mode (Portable Charger):

- Any 12V electrical or electronic accessory or appliance, including Apple devices


JUMP STARTER USE:

- Access the Battery Compartment of your Volkswagen (or of the Motorcycle or Watercraft)
- Connect the Wiring Harness that has the two Pliers (Red and Black) at one end, and the Blue Plug at the other, to the Jump Starter
- Switch on the Jump Stater By pressing the only available button, to check the charge status
- Connect the Red Pliers to the Positive Pole, the Black Pliers to the Negative Pole (NO FEAR, if you make a mistake there will be NO sparks)
- After the connection, press the only button on the transformer of the Harness, if connected correctly a green light will turn on; if it is red, invert the polarity or check the clamp connection and press the button again
- A green light proceed with starting the vehicle

POWERBANK USE:

- Connect the cable needed to power the device you want to charge to a USB or USB-C socket and press the power button
- Wireless recharge, place a device designed for this recharge on the lightning bolt design on the Power Bank and press the power button
- The recharge or flow of current through the cigarette lighter takes place by connecting the DC plug, which has the cigarette lighter input at the end; Therefore insert the cigarette lighter socket and press the ignition button




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article. as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY ERRONEY PURCHASES

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Volkswagen Golf

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Volkswagen Golf

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Volkswagen Golf

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For VOLKSWAGEN GOLF with Roof Bars, Already Installed



ASSEMBLY:

- Place the roof box on the roof bars of your vehicle.
- At the base of the box, drill with a screwdriver the appropriate points, in correspondence with your bars.
- Insert the "U" brackets from the bottom towards the top, making them cross the box
- Screw with the pins supplied from inside the box, until it is correcty locked.


Although mouting is simple and intuitive, FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT.
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- For Volkswagen Golf 7 Pre-Facelift, (2012-2017)

**Attention! NOT COMPATIBLE with GTI, GTD, R-LINE versions**


ASEMBLY:

ATTENTION: Although double-sided adhesive tape is supplied, for a perfect hold, it is recommended to glue the spoiler to the bodywork with appropriate professional mastics.

- Thoroughly wash and clean the surface to which the spoiler is to be applied.
- Adhere the spoiler to the desired part with bodywork mastics
- Use a bodywork dryer to finish fixing
- Do not expose to humidity for 32h




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for VW Golf

**Attention! NO for GTI Sports Versions**

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for VW Golf

**Attention! NO for GTI Sports Versions**

(Eligible for Reclining Seats, Seats with Integrated AIRBAG, Rear seats with central armrest, Folding or Partially Folding Rear Seats)


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- If the car is equipped with folding rear seats, lower the zip at the joint and partially fold the backrest
- By lowering the backrest, you will have access to the unfinished side: add the side covers by closing the zip on both unfinished sides
(Attention: The two Side Covers Are Attached to each other by an Elastic; if necessary, detach them with a cut)
- Tighten and Fix the Elastics of the Side Covers Behind the Back, using the Special Metal Hooks Provided
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)