COMPATIBILITY:

- For BMW 3 SERIES (G20 G21) Pre-Facelift, 2019-2022
Suitable for both Versions, with and without front Camera Sensor


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 3 SERIES GT (F34), 2012-2020


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW X3 (F25) Facelift, 2014-2017


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW X4 (F26), 2014-2018


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 6 SERIES GT (G32) Pre-Facelift 2017-2020


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 1 SERIES (F20-F21) Pre-Facelift 2011-2015


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 3 SERIES (F30-F31), 2012-2019


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 3 SERIES (E46) Facelift 2001-2005


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 1 SERIES (F20-F21) Facelift 2015-2018


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW X3 (F25) Pre-Facelift, 2010-2014


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 3 SERIES (E90 E91) Facelift 2008-2013


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 1 SERIES (E87-E81) Facelift 2007-2012
- For BMW 1 SERIES (E82-E88) 2007-2013


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 3 SERIES (E90-E91) Pre-Facelift 2005-2008


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 5 SERIES GT (F07), 2009-2017


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 3 SERIES (E92-E93) Coupe, Convertible - Facelift 2010-2014



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 4 SERIES (F32, F33, F36), 2013-2019
- For BMW SERIE M4 (F82, F83), 2013-2019


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 2 SERIES (F22-F23) 2014-2021


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 5 SERIES (E39), 1995-2003


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- For BMW 3 SERIES (E92-E93) Coupe, Convertible - Pre-Facelift 2006-2009



ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.