COMPATIBILITY:

- For VOLKSWAGEN T-CROSS (from 2019), Low Beam



FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

- ADAPTERS:

All cars that do not have the STANDARD LOCKING CLIP to lock the halogen bulb, may need simple ADAPTERS; found them in OUR STORE.
IMPORTANT: Their compatibility could not always depend on the model of your car; it depends mainly on the LOCKING SYSTEM of the halogen bulbs of your headlight.

COMPATIBILITY:

- Volkswagen T-Cross (from 2019), with Tires:

195/60 R16
205/60 R16
205/55 R17
215/45 R18

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY:

- Volkswagen T-Cross from 2019


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Volkswagen T-Cross from 2019


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Volkswagen T-Cross from 2019


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Specific for Volkswagen T-Cross


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Specific for Volkswagen T-Cross


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Volkswagen T-Cross with Wheels Between 14 Inches and 18 Inches
- Tire Width not Exceeding 245


USE:

- Use of Wheel Covering, Storage, Transport
- Insert the tire inside the bag by rolling it on it
- Close the strap with the internal Velcro
- Close Clips
- Insert Pins Into The Outer Hook Pocket

COMPATIBILITY:

- For Volkswagen T-Cross (from 2019), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- VOLKSWAGEN SUV

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- VOLKSWAGEN SUV

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Volkswagen T-Cross (from 2019), With Manual Gearbox


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers




Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Volkswagen AMAROK
- Volkswagen T-ROC
- Volkswagen T-CROSS
- Volkswagen TIGUAN
- Volkswagen TOUAREG


It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Volkswagen AMAROK
- Volkswagen T-ROC
- Volkswagen T-CROSS
- Volkswagen TIGUAN
- Volkswagen TOUAREG

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Suitable for VOLKSWAGEN Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for VOLKSWAGEN Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for VOLKSWAGEN Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- For VOLKSWAGEN cars

It is applicable on any vehicle with an Indentation on the bumper where it will be possible to fix the bracket (LOOK AT THE PHOTO).



ASSEMBLY:

- Put the plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the Screws

- Remove the plate and apply it on the new plate holder

- Apply the chromed frame and Fix it with the 4 screws supplied




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For VOLKSWAGEN Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For VOLKSWAGEN Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For VOLKSWAGEN Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- On Bodywork, Rubber, Plastics, Metals "After Washing" of your Volkswagen
- Can be used on previously treated or waxed bodywork without worrying about damaging any layers, on the contrary it reinforces them
- Do not use on glass or mirrors


APPLICATION:

- Spray the Vehicle with Water or Wash it
- Thoroughly dry the car
- Dilute 50ml of Nanotechnological Hydro Wax in 450ml of water
- Apply the product with a professional sponge
- Rinse with Clean Water
- Polish with a clean microfiber cloth




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
We trust in your common sense.

COMPATIBILITY:

- On Tyres External Edging of your Volkswagen


APPLICATION: 1 With a Sponge, Cloth or Brush - 2 With a Spray Bottle
'' IT IS POSSIBLE TO APPLY IT WITHOUT DILUTING IT or with a little water, having a MORE INTENSE EFFECT with a more Strong colour"

1
- Thoroughly clean the tires before application
- Dilute 50Ml of Concentrate in 200Ml of Water in a Plastic Bucket
- Apply the product with a sponge, cloth or brush
- Wait for Drying

2
- Thoroughly clean the tires before application
- Dilute 1 Part Concentrate in 2-4 Parts Water and Insert it into a Spray Applicator
- Apply the product with a spray bottle
- Wait for Drying




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
We trust in your common sense.