Alfa 4C | Tuning Accessories and Xenon LED Lights

LED Bulbs LOW + HIGH BEAM for Alfa Romeo 4C | CANbus, White Light 6500K Professional

-6%

LED Bulbs LOW + HIGH BEAM for Alfa Romeo 4C | CANbus, White...

COMPATIBILITY:

- For Alfa Romeo 4C (2013-2019), Lowbeam + Highbeam

FOR AN OPTIMUM MOUNTING, WE RECOMMENDS:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.

NON-STANDARD CASES

- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

€134.41 €142.99

H7 LED Kit for ALFA ROMEO 4C Low Beam | LED Bulbs CANbus 6500K 12000LM

-6%

H7 LED Kit for ALFA ROMEO 4C Low Beam | LED Bulbs CANbus 6500K...

COMPATIBILITY:

- ALFA ROMEO 4C with HALOGEN H7 BULBS
- Lenticular Headlight (With Lens)

FOR AN OPTIMUM MOUNTING, WE RECOMMENDS:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.

NON-STANDARD CASES

- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

€75.19 €79.99

Snow Socks for Alfa 4C, EN-APPROVED for Italy and Europe | Alternative Snow Chains

-5%

Snow Socks for Alfa 4C, EN-APPROVED for Italy and Europe |...

COMPATIBILITY:

- Alfa romeo 4C (13-19), with Tires:

235/40 R18
205/40 R18
235/35 R19

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.

We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

€61.73 €64.98

H7 LED Kit for Alfa Romeo 4C Low Beam CANbus Bulbs | 6500K Cool White 8000LM

-4%

H7 LED Kit for Alfa Romeo 4C Low Beam CANbus Bulbs | 6500K...

COMPATIBILITY:

- For Lowbeam Alfa Romeo 4C (2013-2019)

FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.

NON-STANDARD CASES

- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

€61.88 €64.46

Car SEAT COVER Suitable for Alfa Romeo Seat | ANTI SWEAT in Black Breathable Fabric | Front Seat, Professional Use

-5%
Out of Stock

Car SEAT COVER Suitable for Alfa Romeo Seat | ANTI SWEAT in...

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG

INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.

(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

€37.03 €38.98

2 Wiper Blades for Alfa 4C Front HEYNER GERMANY FLAT NANO Graphited | AWARD-WINNING

-1%

2 Wiper Blades for Alfa 4C Front HEYNER GERMANY FLAT NANO...

COMPATIBILITY:

- For Alfa Romeo 4C (13-19), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car

FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.

We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

€38.57 €38.96

Front LICENSE PLATE Holder for Alfa Romeo Bracket SIDE RELOCATOR In Anodized STEEL tuning

-1%

Front LICENSE PLATE Holder for Alfa Romeo Bracket SIDE...

COMPATIBILITY:

- For ALFA ROMEO Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).

ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)

FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€19.06 €19.25

Front License Plate Holder for Alfa Romeo, Side Relocator Bracket, in Anodized Red Steel

-1%

Front License Plate Holder for Alfa Romeo, Side Relocator...

COMPATIBILITY:

- For ALFA ROMEO Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).

ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)

FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

€19.06 €19.25

2 LED Licence Plate Light for Alfa Romeo 4C (13-19) | T10 W5W Bulbs 6500K Ice White, 100% CANBUS Error Free

-4%
Out of Stock

2 LED Licence Plate Light for Alfa Romeo 4C (13-19) | T10 W5W...

COMPATIBILITY:

- Alfa Romeo 4C (2013-2019), LICENSE PLATE LIGHTS

UNDERSTAND THE PURCHASE AND HOW TO CHOOSE THE BEST BULB:

THE DECEPTION OF BULBS WITH LOTS OF LEDS: The most common and BIGGEST PURCHASE MISTAKE happens in thinking that bulbs with more LEDs are better than those with less leds.

- The more the LEDs are on a plate / The shorter the distance between the LEDs is / the less they will last, since the greater the possibility that the LEDs will burn soon is, leading to malfunction, short-circuits, or lightning.

THE BAD ENEMY OF THE LED is the '' HEAT '', so if there are too many LEDs on a plate, or if they are too close, THE HEAT will cause the consequences described above

THIS TYPE OF BULBS USES THE AESTHETIC FACTOR OF SEEING LOTS OF LEDS AS A SHIELD OF USING A CHEAPEST AND LOW QUALITY PLATE

The greater the cooling area will be, the longer their DURABILITY and RELIABILITY will be

€13.43 €13.99

2 LED Licese Plate Light for Alfa Romeo 4C (13-19) | T10 W5W Bulbs White Light 6500K, 100% CANBUS Error Free

-4%
Out of Stock

2 LED Licese Plate Light for Alfa Romeo 4C (13-19) | T10 W5W...

COMPATIBILITY:

- Alfa Romeo 4C (2013-2019), LICENSE PLATE LIGHTS

UNDERSTAND THE PURCHASE AND HOW TO CHOOSE THE BEST BULB:

THE DECEPTION OF BULBS WITH LOTS OF LEDS: The most common and BIGGEST PURCHASE MISTAKE happens in thinking that bulbs with more LEDs are better than those with less leds.

- The more the LEDs are on a plate / The shorter the distance between the LEDs is / the less they will last, since the greater the possibility that the LEDs will burn soon is, leading to malfunction, short-circuits, or lightning.

THE BAD ENEMY OF THE LED is the '' HEAT '', so if there are too many LEDs on a plate, or if they are too close, THE HEAT will cause the consequences described above

THIS TYPE OF BULBS USES THE AESTHETIC FACTOR OF SEEING LOTS OF LEDS AS A SHIELD OF USING A CHEAPEST AND LOW QUALITY PLATE

The greater the cooling area will be, the longer their DURABILITY and RELIABILITY will be

€11.40 €11.87

2 Adapters Bulbs Holder for LED KIT H7 Installation for Alfa Romeo 4C (2013-2019)

-9%

2 Adapters Bulbs Holder for LED KIT H7 Installation for Alfa...

COMPATIBILITY:

- Alfa Romeo 4C (2013-2019)

CAUTION:

- It is compatible ONLY with PROFESSIONAL led / xenon kits (BECAUSE they have standard dimensions and removable ring)
- The compatibility of the adapter is dictated, regardless of the year and vehicle model, by the type of halogen bulb locking inside the headlight.
WE RECOMMEND before proceeding with the purchase, to compare the shape of the adapter with the locking system of the halogen bulb.

INSTRUCTION:

- Remove the ring from the LED bulb with a rotating movement

- Insert the adapter on the bulb

- Mount the ring nut again, locking the adapter

- Proceed now with the installation of the Led or Xenon bulb inside the headlight, now fitted with a locking adapter

FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT

We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

€10.24 €11.25

LED REVERSE Light for Alfa Romeo 4C (13-19) | 1pc T15 W16W Led Bulb 6500K Ice White | 100% CANBUS Error Free

-4%

LED REVERSE Light for Alfa Romeo 4C (13-19) | 1pc T15 W16W Led...

COMPATIBILITY:

- Alfa Romeo 4C (2013-2019), REVERSE LIGHT

UNDERSTAND THE PURCHASE AND HOW TO CHOOSE THE BEST BULB:

THE DECEPTION OF BULBS WITH LOTS OF LEDS: The most common and BIGGEST PURCHASE MISTAKE happens in thinking that bulbs with more LEDs are better than those with less leds.

- The more the LEDs are on a plate / The shorter the distance between the LEDs is / the less they will last, since the greater the possibility that the LEDs will burn soon is, leading to malfunction, short-circuits, or lightning.

THE BAD ENEMY OF THE LED is the '' HEAT '', so if there are too many LEDs on a plate, or if they are too close, THE HEAT will cause the consequences described above

THIS TYPE OF BULBS USES THE AESTHETIC FACTOR OF SEEING LOTS OF LEDS AS A SHIELD OF USING A CHEAPEST AND LOW QUALITY PLATE

The greater the cooling area will be, the longer their DURABILITY and RELIABILITY will be

€10.54 €10.98

Left Banner

4C (13-19)

Join Our Newsletter

Info About QualitySPCars

Easy Shopping

Free shipping (Italy)

Flash Shipping

Return an Item

6/7 Assistance - Chat with us

30 Day Return, 0 Worries

Safe Payments

Shipping Partners

Left Banner  