A1 8X Facelift (15-18)

Accessories and LED Lights for Audi A1 8X 15-18 Tuning | QSPCARS

Active Filters

  • Color: Anodized Red
  • Color: Metallic Silver
  • Color: Translucent Black - Red Light

There Are 3 Products.

Sort by:
Sales, highest to lowest Relevance Name, A to Z Name, Z to A Price, low to high Price, high to low Reference, A to Z Reference, Z to A
Rear Adhesive LED SPOILER For Audi A1 | Roof LED Strip in Translucent Black
  • -5%
  • New
  • Out of Stock
Add to Wishlist
Rear Adhesive LED SPOILER For Audi A1 | Roof LED Strip in...
COMPATIBILITY:

- Specific for Audi A1


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

Add to Wishlist
€47.47 Regular Price €49.97
Front License Plate Holder for Audi, Side Relocator Bracket, in Anodized Red Steel
  • -1%
  • New
Add to Wishlist
Front License Plate Holder for Audi, Side Relocator Bracket,...
COMPATIBILITY:

- For AUDI Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

Add to Wishlist
€19.06 Regular Price €19.25
Professional CROSS KEY Suitable for Audi Wheels | in Hardened STEEL | Bolts 17 - 19 - 21 - 23
  • -3%
  • New
Add to Wishlist
Professional CROSS KEY Suitable for Audi Wheels | in Hardened...
COMPATIBILITY:

- Wheels Vehicles, including Audi
- Nuts 17, 19, 21, 23

USE:

1) The bolts must be unscrewed before lifting the car, on a flat, stable and safe surface.
2) Insert the jack under the frame in the position indicated in the use and maintenance handbook.
3) Raise the jack just enough to tension it in the right position to support the car but without lifting it off the ground.
4) Remove the hubcap and loosen the nuts by turning the cross wrench counterclockwise.
5) The tire must be left in contact with the ground because in this way the force applied makes the nuts turn but not the wheel, which remains blocked by the ground.
6) The nuts must not be unscrewed completely but you must limit yourself to overcoming the resistance of the tightening.
7) Raise the car, completing the operation of unscrewing the bolts and removing the wheel which must be completed by hand.

The same operation must be done in reverse when refitting the replaced wheel, tightening the bolts last, to be carried out when the vehicle is already on the ground.
Add to Wishlist
€17.42 Regular Price €17.96