LED DRL Daytime Running Lights & Stop

Hyundai with Daytime Running Lights in Headlight

DRL DAYTIME LIGHTS & LED BRAKE LIGHTS


Renew the Look of Your Car by Adding LED DRL Strips or LED Brake Lights.

DRL Lights (Day Running Light) or Daytime Running Lights Improve the Visibility of the Vehicle Giving a More Current Look in Line with Innovation.

QSPCARS LED Accessories Are Never Invasive, Our Task Is to Modify the Lights While Preserving the Original Component.

Car Approved LED Daytime Running Lights DRL Universal | QSPCARS

Active Filters

  • Color: 6500K Ice White - 2000K Yellow Amber Lights
  • Color: Translucent Black Dish - 6.500K Ice White Light
Universal DRL LED Round Fog Lights APPROVED with Powerful White LED Daytime Running Lights
  • -2%
  • New
  • Out of Stock
Universal DRL LED Round Fog Lights APPROVED with Powerful...
COMPATIBILITY

- Vehicles 8-32V (CAR, TRUCK) with 3.5 Inch (90MM) round headlights
- Distance Between Fixing Holes (4 Holes): Width: 100mm - Height: 50m


ASSEMBLY INSTRUCTIONS:

1) Remove the old Fog Lights, and disconnect them, or create the accommodation for the new Fog Lights
2) Connect the supplied cables to the fog light, as explained in point 3:
3) Connect the control unit to the fog light using the round 4-pin plug (remember, the wiring diagram is shown on the control units)
FROM THE CONTROL UNIT THERE IS A DIRECTION OF TWO CABLES, respectively:
- a cable H8 - H11 - H9 - H16, which will be connected to the car power supply (This socket also acts as a Negative Pole, in fact, if not connected, the DRLs will not turn on)
- a double color cable (yellow-red), to which it will be necessary to connect the yellow-red extension cable, also supplied (this cable will be the power supply of the DRL lights)
4) Connect the Red Cable to the positive pole of the Battery
5) Connect the Yellow Cable to the negative pole of the battery, or to the negative pole of the headlights
6) Connect the second fog light to the second control unit, as already done for the first fog light
7) In this case, at the branch of the double cable of the control unit, the yellow-red cable must be connected in a chain to the wiring of the first spot, using the plug, on the yellow-red cable


FOR OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT


- the fixture has a socket H8 - H11 - H9 - H16> 9005 - HB3 - H10> 9006 - HB4, therefore in most cases it will not be necessary to make changes to the wiring, the PLUG AND PLAY rule will apply (connection only)

On some cars, it may be necessary to make small changes during installation. We always trust in your common sense.



We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES
€189.26 Regular Price €193.12
2 Flexible LED Strips DRL, Daytime Running Light + Sequential...
COMPATIBILITY:

Universal, Suitable for Cars and Motorcycles


INSTRUCTIONS:

You can install them on headlights, bumpers, hood, fog lights

- Carefully clean by removing the Surface where to install the LED Strip from any Impurities.

- Connect Black Wire to Earth (Battery Negative Pole)

- Connect the red wire to the parking lights or under the key

- Connect the yellow wire to the positive pole of the Turn Signal

- Check the required length, proceed to cut the excess strip** at the points indicated on the back of the LED strip.

- Remove Adhesive Protective Film and adhere LED Strip on the Desired Point
(Taking care that the surface is completely dry and free of all impurities)

- Heat everything with a thermal hairdryer at a suitable distance to make the adhesive adhere perfectly (cold months).

DO NOT wash or rinse for 72H

** If possible, avoid cutting the band, as although prepared, unfortunately the warranty will expire after the modification **


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

We do not take responsibility for: incorrect purchases-violations of regulations or laws of any state-damages, which you could cause to yourself, to third parties or to the same article. as we describe every single specification in detail.

€36.85 Regular Price €37.99
2 Flexible LED Strips DRL, Daytime Running Light + Sequential...
COMPATIBILITY:

Universal, Suitable for Cars and Motorcycles


INSTRUCTIONS:

You can install them on headlights, bumpers, hood, fog lights

- Carefully clean by removing the Surface where to install the LED Strip from any Impurities.

- Connect Black Wire to Earth (Battery Negative Pole)

- Connect the red wire to the parking lights or under the key

- Connect the yellow wire to the positive pole of the Turn Signal

- Check the required length, proceed to cut the excess strip** at the points indicated on the back of the LED strip.

- Remove Adhesive Protective Film and adhere LED Strip on the Desired Point
(Taking care that the surface is completely dry and free of all impurities)

- Heat everything with a thermal hairdryer at a suitable distance to make the adhesive adhere perfectly (cold months).

DO NOT wash or rinse for 72H

** If possible, avoid cutting the band, as although prepared, unfortunately the warranty will expire after the modification **


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

We do not take responsibility for: incorrect purchases-violations of regulations or laws of any state-damages, which you could cause to yourself, to third parties or to the same article. as we describe every single specification in detail.

€34.91 Regular Price €35.99