COMPATIBILITY:

- For Lowbeam BMW 1 Series F20, F21 Facelift (2015-2018)


FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

- ADAPTERS:

All cars that do not have the STANDARD LOCKING CLIP to lock the halogen bulb, may need simple ADAPTERS; found them in OUR STORE.
IMPORTANT: Their compatibility could not always depend on the model of your car; it depends mainly on the LOCKING SYSTEM of the halogen bulbs of your headlight.

COMPATIBILITY:

- BMW 1 series F20/ F21 Facelift (2015-2018) WITH STANDARD BI-XENON SYSTEM


MOUNTING:

- Replace the original bulbs by connecting the NEW REPLACEMENT BULBS


FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT

COMPATIBILITY:

- For BMW 1 Series F20 F21 (2011-2015), with Automatic Gearbox
- For BMW 1 Series F20 Facelift (2015-2018), with Automatic Gearbox

**Attention: Check the Shape of the Side of the Accelerator Pedal (see photo n.2)**


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers (The accelerator pedal must be inserted from top to bottom)
3) Attach the Footrest Using the Adhesive on the Back



Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- For BMW 1 Series F20 F21 (2011-2018), with Automatic Gearbox

**Attention: Check the Shape of the Side of the Accelerator Pedal (see photo n.2)**


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers (The accelerator pedal must be inserted from top to bottom)



Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- For BMW 1 Series F20 F21 (2011-2018), with Automatic Gearbox

**Attention: Check the Shape of the Side of the Accelerator Pedal (see photo n.2)**


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers (The accelerator pedal must be inserted from top to bottom)



Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- All Vehicles with Roof Bars


REQUIREMENTS:

- WHEEL WIDTH: from 25 mm to 35 mm
- BIKE FRAME DIAMETER: Ø from 28 mm to 40 mm
- ROOF BARS: Maximum 48 mm (Width) x 40 mm (Height)
- MAXIMUM LOAD WEIGHT: 15 Kg


INSTALLATION:

(Instructions Supplied)

- Secure the Frame Holder Pliers to each other, by means of the Special Spring + Bolt + Washer
- Attach the frame holder bracket to the front of the duct
- Screw the front part of the duct to the rear part
- Fix the Duct, complete with the Shelter Bracket, to the Car Roof Bars
- Secure the bike to the bike carrier by tightening the frame holder clamps and locking the wheels with the appropriate straps




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Bmw 1 Series F20 Facelift (15-18), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- BMW 1-3 SERIES

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW 1-3 SERIES

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW 1 Series F20-F21-F40

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW 1-2 Series-i3

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 1 Series (F20, F21) 2011-2015
- 1 Series (F20) Facelift 2015-2018

ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 1 Series (F20, F21) 2011-2015
- 1 Series (F20) Facelift 2015-2018


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 1 Series (F20, F21) 2011-2015
- 1 Series (F20) Facelift 2015-2018

ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 1 Series (F20, F21) 2011-2015
- 1 Series (F20) Facelift 2015-2018


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 1 Series (F20, F21) 2011-2015
- 1 Series (F20) Facelift 2015-2018


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- BMW 1 Series F20 - F21 Facelift (from 2015) x 2Pz


INSTRUCTION:

- Remove the current plates, using a screwdriver if necessary, inserting the tip in the side part of the plate and apply pressure towards the outside: the plate will come out.

- Disconnect the cable and disconnect definitely the plate.

- Connect the new LED PLATE to the cable and replace it inside the housing. Repeat the same operation with the second plate.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY:

FOR BMW - COURTESY DOOR LIGHTS:

- 1 Series F20 - F21 (from 2011) x 2Pz


INSTRUCTION:

- Remove the current led plates, using a screwdriver if necessary, inserting the tip in the side part of the plate and apply pressure towards the outside: the plate will come out.

- Disconnect the cable and disconnect definitely the plate.

- Connect the new LED PLATE to the cable and replace it inside the housing. Repeat the same operation with the second plate.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY:

Correspondence with Original Part Number: 63267193294

BMW:

- 1 Series (F20, F21) Facelift 2015-2018


INSTRUCTION:

- Remove the current led plates, using a screwdriver if necessary, inserting the tip in the side part of the plate and apply pressure towards the outside: the plate will come out.

- Disconnect the cable and disconnect definitely the plate.

- Connect the new LED PLATE to the cable and replace it inside the housing. Repeat the same operation with the second plate.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY:

- For BMW Cars

It is applicable on any vehicle with an Indentation on the bumper where it will be possible to fix the bracket (LOOK AT THE PHOTO).



ASSEMBLY:

- Put the plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the Screws

- Remove the plate and apply it on the new plate holder

- Apply the chromed frame and Fix it with the 4 screws supplied




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.