COMPATIBILITY:

- For BMW 3 SERIES (G20 G21) Pre-Facelift, 2019-2022
Suitable for both Versions, with and without front Camera Sensor


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

- Bmw 3 Series G20 (19-22), with Tires:

205/60 R16
225/50 R17
225/45 R18
255/40 R18
225/40 R19
255/35 R19
255/30 R20
225/35 R20

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY:

- Specific for Bmw Serie 3


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Specific for Bmw Serie 3


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- All Vehicles with Roof Bars


REQUIREMENTS:

- WHEEL WIDTH: from 25 mm to 35 mm
- BIKE FRAME DIAMETER: Ø from 28 mm to 40 mm
- ROOF BARS: Maximum 48 mm (Width) x 40 mm (Height)
- MAXIMUM LOAD WEIGHT: 15 Kg


INSTALLATION:

(Instructions Supplied)

- Secure the Frame Holder Pliers to each other, by means of the Special Spring + Bolt + Washer
- Attach the frame holder bracket to the front of the duct
- Screw the front part of the duct to the rear part
- Fix the Duct, complete with the Shelter Bracket, to the Car Roof Bars
- Secure the bike to the bike carrier by tightening the frame holder clamps and locking the wheels with the appropriate straps




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Bmw 3 Series G20 (19-22), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- BMW 1-3 SERIES

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW 1-3 SERIES

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW 3 Series


It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW 3 Series F30-F31 GT-G20

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 3 Series (G20, G21) from 2019


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 3 Series (G20, G21) from 2019


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 3 Series (G20, G21) from 2019


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 3 Series (G20, G21) from 2019


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

BMW

- 3 Series (G20, G21) from 2019


ASSEMBLY:

- Remove the 2 BMW Grilles using plastic levers, suitable screwdrivers and keys

- Apply the Covers on the Cross Radiator Protection Bars located behind the grilles (The seal is Tested!)

- Proceed with the assembly of the previously disassembled Grilles




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- For BMW Cars

It is applicable on any vehicle with an Indentation on the bumper where it will be possible to fix the bracket (LOOK AT THE PHOTO).



ASSEMBLY:

- Put the plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the Screws

- Remove the plate and apply it on the new plate holder

- Apply the chromed frame and Fix it with the 4 screws supplied




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For BMW Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For BMW Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For BMW Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- On Tyres External Edging of your Bmw


APPLICATION: 1 With a Sponge, Cloth or Brush - 2 With a Spray Bottle
'' IT IS POSSIBLE TO APPLY IT WITHOUT DILUTING IT or with a little water, having a MORE INTENSE EFFECT with a more Strong colour"

1
- Thoroughly clean the tires before application
- Dilute 50Ml of Concentrate in 200Ml of Water in a Plastic Bucket
- Apply the product with a sponge, cloth or brush
- Wait for Drying

2
- Thoroughly clean the tires before application
- Dilute 1 Part Concentrate in 2-4 Parts Water and Insert it into a Spray Applicator
- Apply the product with a spray bottle
- Wait for Drying




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
We trust in your common sense.