COMPATIBILITY

(NB: They replace the Series Halogen lamps that illuminate the Angel Eyes Rings; they do not create them if you do not own them)

- BMW X3 E83 (From 2006 to 2010) FACELIFT, With Xenon Headlights


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

- DISASSEMBLY OF ITS HALOGEN Unscrewing the locking screws.

- CONTROL: Connect only the LED socket (PLUG AND PLAY); if there are no problems, proceed with the assembly.

- LOCK ON THE CAR: Screwing the new screws supplied





We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- Bmw X3 E83 (04-10), with Tires:

215/60 R17
235/55 R17
235/50 R18
255/45 R18
235/45 R19
255/40 R19

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY:

- For Lowbeam BMW X3 E83 (2004-2010)



FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

- ADAPTERS:

All cars that do not have the STANDARD LOCKING CLIP to lock the halogen bulb, may need simple ADAPTERS; found them in OUR STORE.
IMPORTANT: Their compatibility could not always depend on the model of your car; it depends mainly on the LOCKING SYSTEM of the halogen bulbs of your headlight.

COMPATIBILITY

(NB: They replace the Series Halogen lamps that illuminate the Angel Eyes Rings; they do not create them if you do not own them)

- BMW X3 E83 (From 2006 to 2010) FACELIFT, With Xenon Headlights


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

- DISASSEMBLY OF ITS HALOGEN Unscrewing the locking screws.

- CONTROL: Connect only the LED socket (PLUG AND PLAY); if there are no problems, proceed with the assembly.

- LOCK ON THE CAR: Screwing the new screws supplied





We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- Specific for Bmw X3


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW X3 E83 Facelift (2006-2010) WITH STANDARD XENON SYSTEM

ATTENTION If Pre-Facelift UP TO 2006, Check in our store right Bulbs


MOUNTING:

- Replace the original bulbs by connecting the NEW REPLACEMENT BULBS


FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT

COMPATIBILITY:

- Specific for Bmw X3


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For Bmw X3 E83 (2004-2010), with Automatic Gearbox


INSTALLATION:

1) Remove the rubber pedal cover only for the brake, for the accelerator and the foot rest The fixing will be carried out directly on the existing support
2) Place the new pedal covers on the pedals and, through the holes present, make marks on the pedal in the 4 fixing corners
3) Move the new pedal covers and now drill the 4 traced slots with a drill and 3mm bit
4) Clean the Pedals and Position the new Pedal Covers which will be fixed with Bolts, Washers and Nuts present in the Fixing Kit
5) When fixing, position the washer in the front part of the pedal cover and immediately after the bolt, in the rear part position the ring followed by the nut and screw
6) Tighten the screwing with the spanner present in the fixing kit
7) Follow the same procedure for the Accelerator and Foot Rest pedal


Attention: the Foot Rest will be fixed with the Self-tapping Screws always present in the Fixing Kit.


Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- All Vehicles with Roof Bars


REQUIREMENTS:

- WHEEL WIDTH: from 25 mm to 35 mm
- BIKE FRAME DIAMETER: Ø from 28 mm to 40 mm
- ROOF BARS: Maximum 48 mm (Width) x 40 mm (Height)
- MAXIMUM LOAD WEIGHT: 15 Kg


INSTALLATION:

(Instructions Supplied)

- Secure the Frame Holder Pliers to each other, by means of the Special Spring + Bolt + Washer
- Attach the frame holder bracket to the front of the duct
- Screw the front part of the duct to the rear part
- Fix the Duct, complete with the Shelter Bracket, to the Car Roof Bars
- Secure the bike to the bike carrier by tightening the frame holder clamps and locking the wheels with the appropriate straps




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Bmw X3 E83 (04-10), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY

- BMW X3 (E83) 2004-2010


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT

- Remove your own side marker, pusching and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, remove the double-sided tape from the Led Side Marker, connect the socket to the new Led Side Marker, repeat the same operations to fix it in its place. Press the Led Side Marker so to led the double-sided tape adhere perfectly.

REMEMBER: for a perfect assembly, we always recommend replacing the double-sided tape with a new one; the articles remain on stock long time, they could be subject to small sources of humidity and glue could lose its original efficiency ... in this way you can get a perfect result





YOU COULD INSTALL THEM ON MANY OTHER CARS, ALSO NOT BMW BRANDED, BUT:
We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY

- BMW X3 (E83) 2004-2010


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT

- Remove your own side marker, pusching and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, remove the double-sided tape from the Led Side Marker, connect the socket to the new Led Side Marker, repeat the same operations to fix it in its place. Press the Led Side Marker so to led the double-sided tape adhere perfectly.

REMEMBER: for a perfect assembly, we always recommend replacing the double-sided tape with a new one; the articles remain on stock long time, they could be subject to small sources of humidity and glue could lose its original efficiency ... in this way you can get a perfect result





YOU COULD INSTALL THEM ON MANY OTHER CARS, ALSO NOT BMW BRANDED, BUT:
We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY:

- BMW SUV

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW SUV

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY

- BMW X3 (E83) 2004-2010


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT

- Remove your own side marker, pusching and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, remove the double-sided tape from the Led Side Marker, connect the socket to the new Led Side Marker, repeat the same operations to fix it in its place. Press the Led Side Marker so to led the double-sided tape adhere perfectly.

REMEMBER: for a perfect assembly, we always recommend replacing the double-sided tape with a new one; the articles remain on stock long time, they could be subject to small sources of humidity and glue could lose its original efficiency ... in this way you can get a perfect result





YOU COULD INSTALL THEM ON MANY OTHER CARS, ALSO NOT BMW BRANDED, BUT:
We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY

- BMW X3 (E83) 2004-2010


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT

- Remove your own side marker, pusching and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, remove the double-sided tape from the Led Side Marker, connect the socket to the new Led Side Marker, repeat the same operations to fix it in its place. Press the Led Side Marker so to led the double-sided tape adhere perfectly.

REMEMBER: for a perfect assembly, we always recommend replacing the double-sided tape with a new one; the articles remain on stock long time, they could be subject to small sources of humidity and glue could lose its original efficiency ... in this way you can get a perfect result





YOU COULD INSTALL THEM ON MANY OTHER CARS, ALSO NOT BMW BRANDED, BUT:
We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY

- BMW X3 (E83) 2004-2010


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT

- Remove your own side marker, pusching and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, remove the double-sided tape from the Led Side Marker, connect the socket to the new Led Side Marker, repeat the same operations to fix it in its place. Press the Led Side Marker so to led the double-sided tape adhere perfectly.

REMEMBER: for a perfect assembly, we always recommend replacing the double-sided tape with a new one; the articles remain on stock long time, they could be subject to small sources of humidity and glue could lose its original efficiency ... in this way you can get a perfect result





YOU COULD INSTALL THEM ON MANY OTHER CARS, ALSO NOT BMW BRANDED, BUT:
We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY:

- BMW X3 (E83) 2004-2010


INSTRUCTIONS:


- Remove your own side marker, pusching and sliding it forward or backward (IT WILL SPIT)
- Disconnect the socket, remove the double-sided tape from the Led Side Marker, connect the socket to the new Led Side Marker, repeat the same operations to fix it in its place. Press the Led Side Marker so to led the double-sided tape adhere perfectly.

REMEMBER: for a perfect assembly, we always recommend replacing the double-sided tape with a new one; the articles remain on stock long time, they could be subject to small sources of humidity and glue could lose its original efficiency ... in this way you can get a perfect result


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMENDS THE INSTALLATION BY AN EXPERT



YOU COULD INSTALL THEM ON MANY OTHER CARS, ALSO NOT BMW BRANDED, BUT:
We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY:

- BMW X3 E83 Pre-Facelift (2004-2006) WITH STANDARD XENON SYSTEM

ATTENTION If Facelift FROM 2006, Check in our store right Bulbs


MOUNTING:

- Replace the original bulbs by connecting the NEW REPLACEMENT BULBS


FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT

COMPATIBILITY:

- BMW X3 (E83) 2004-2010



INSTRUCTIONS:

- Remove your own side marker, pusching and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, remove the double-sided tape from the Led Side Marker, connect the socket to the new Led Side Marker, repeat the same operations to fix it in its place. Press the Led Side Marker so to led the double-sided tape adhere perfectly.

REMEMBER: for a perfect assembly, we always recommend replacing the double-sided tape with a new one; the articles remain on stock long time, they could be subject to small sources of humidity and glue could lose its original efficiency ... in this way you can get a perfect result


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT



YOU COULD INSTALL THEM ON MANY OTHER CARS, ALSO NOT BMW BRANDED, BUT:
We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. WE WILL NOT ACCEPT RETURNS FOR INCOMPATIBILITY or WRONG PURCHASES

COMPATIBILITY:

- BMW X1-X2-X3

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW X1-X2-X3

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

Bmw:

- X3 (E83) 2004-2010


Code OEM : 63137165914, 63137253326, 63137165915, 63137253325, 63137165913, 63137165916


INSTRUCTIONS:

- Remove your side marker, pushing and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, and connect it to the New one, Repeat the same operation on the CONTRARY.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT



We do not take responsibility for: erroneous purchases-violations of regulations or laws of any state-damages, which could cause you, third parties or the same article. as we describe every single specification in detail.