COMPATIBILITY:

- For BMW X5 (E70), 2006-2013


ASSEMBLY:

Simply to replace the current ones as perfect Spare part: 100% TESTED COMPATIBILITY, BUT:

Although simple and intuitive FOR AN OPTIMAL FITTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT


It is possible to install this item in 2 different ways:

1) Without Bumper Removal (Hard)
2) Removing the Bumper (Simple)

1) In the absence of suitable dexterity, experience and equipment, with this method of assembly it is possible to cause damage to yourself, to the product and to the car.

- Opening the Engine Compartment Bonnet
- Removal of the Bonnet Seal on the Upper Part of the Bumper
- Bumper Top Bolting Removals
- Flex the Upper Part of the Bumper and Check the Positioning of the Upper Clip Hooks of the Old Grille
- Release the old grille by levering the upper clip hooks with a long screwdriver or elongated plastic lever
- Unhooked in the upper part, remove the grill from the front
- Remove the Second Grille by releasing the Clips, thanks to the lateral access freed up with the removal of the first grille
- Affix the New Grilles by hooking the clips with the correct pressure
- Reassemble the bumper and previously removed gasket


2) With the removal of the bumper, the assembly becomes very simple as it is only necessary to release the clips of the old grilles and to reattach the new ones under pressure (operation to be strictly recommended to professionals in the sector)



We do not assume responsibility for: article assembled and subsequently detached, erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, third parties, the vehicle or the article itself, as we describe every single specification in detail.

We also remind you that these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but they remain products that may not be permitted for use on public roads.

We trust in your common sense.

COMPATIBILITY:

BMW - Not suitable for M Sport versions, which already have a tapered mirror caps

- X5 (E70), 2006-2013



ASSEMBLY:

- Using anti-scratch plastic levers (SEARCH FOR THEM IN OUR STORE), pry between the mirror cap and the final black plastic edge.

- Unhooked, remove the Original cap from the Mirror Skeleton.

- Position the New Cap with the plastic joints in correspondence with the slots on the mirror skeleton.

- Apply the correct pressure to make the new cap adhere until it fits completely.



Although simple and intuitive FOR OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not assume responsibility if the item is assembled and subsequently removed.
We trust in your common sense.

COMPATIBILITY:

- BMW X5 (E70) 06-13, Low Beam


FOR AN OPTIMUM MOUNTING, WE RECOMMENDS:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

COMPATIBILITY:

- For BMW X5 E53 (00-06), E70 (06-13), WITH HIGH HANDRAILS (SEE PHOTO)


HANDRAILS NECESSARILY:

- Maximum distance between one and the other 125Cm


ASSEMBLY:

- Insert the lock key to remove the side covers and access the screws below
- Take a screwdriver and unscrew the screws, to make the feet open as much as possible
- Position the Roof Bars by hooking them to the Longitudinal Handrails
- Center the bars on the rails
- Tighten the screws of each foot until it locks correctly WITHOUT FORCE EXCESSIVELY
- Close the side covers by locking them with the key lock




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY

(NB: They replace the Series Halogen lamps that illuminate the Angel Eyes Rings; they do not create them if you do not own them)

- BMW X5 E70 (2006-2013), With Xenon Headlights


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

- DISASSEMBLY OF ITS HALOGEN by unblocking rotary movement.

- CONTROL: Connect only the LED socket (PLUG AND PLAY); if there are no problems, proceed with the assembly

- LOCK ON THE CAR: making a rotary motion





We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- Bmw X5 E70 (06-13), with Tires:

255/55 R18
255/50 R19
285/45 R19
275/40 R20
315/35 R20
285/35 R21
325/30 R21

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY

(NB: They replace the Series Halogen lamps that illuminate the Angel Eyes Rings; they do not create them if you do not own them)

- BMW X5 E70 (2006-2013), With Xenon Headlights


FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION BY AN EXPERT

- DISASSEMBLY OF ITS HALOGEN by unblocking rotary movement.

- CONTROL: Connect only the LED socket (PLUG AND PLAY); if there are no problems, proceed with the assembly

- LOCK ON THE CAR: making a rotary motion






We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- Specific for Bmw X5


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW X5 E70 (2006-2013) WITH STANDARD BI-XENON SYSTEM


MOUNTING:

- Replace the original bulbs by connecting the NEW REPLACEMENT BULBS


FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT

COMPATIBILITY:

- For BMW X5 E70 (2006-2013), with Automatic Gearbox

**Attention: Check the Shape of the Side of the Accelerator pedal (see photo n.2)**


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers (The accelerator pedal must be inserted from top to bottom)
3) Attach the Footrest Using the Adhesive on the Back




Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Specific for Bmw X5


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For Bmw X5 E70 (2006-2013), with Automatic Gearbox


INSTALLATION:

1) Remove the rubber pedal cover only for the brake, for the accelerator and the foot rest The fixing will be carried out directly on the existing support
2) Place the new pedal covers on the pedals and, through the holes present, make marks on the pedal in the 4 fixing corners
3) Move the new pedal covers and now drill the 4 traced slots with a drill and 3mm bit
4) Clean the Pedals and Position the new Pedal Covers which will be fixed with Bolts, Washers and Nuts present in the Fixing Kit
5) When fixing, position the washer in the front part of the pedal cover and immediately after the bolt, in the rear part position the ring followed by the nut and screw
6) Tighten the screwing with the spanner present in the fixing kit
7) Follow the same procedure for the Accelerator and Foot Rest pedal


Attention: the Foot Rest will be fixed with the Self-tapping Screws always present in the Fixing Kit.


Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- All Vehicles with Roof Bars


REQUIREMENTS:

- WHEEL WIDTH: from 25 mm to 35 mm
- BIKE FRAME DIAMETER: Ø from 28 mm to 40 mm
- ROOF BARS: Maximum 48 mm (Width) x 40 mm (Height)
- MAXIMUM LOAD WEIGHT: 15 Kg


INSTALLATION:

(Instructions Supplied)

- Secure the Frame Holder Pliers to each other, by means of the Special Spring + Bolt + Washer
- Attach the frame holder bracket to the front of the duct
- Screw the front part of the duct to the rear part
- Fix the Duct, complete with the Shelter Bracket, to the Car Roof Bars
- Secure the bike to the bike carrier by tightening the frame holder clamps and locking the wheels with the appropriate straps




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Bmw X5 E70 (06-13), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- BMW SUV

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW SUV

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW X4-X5-X6-X7

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW X4-X5-X6-X7

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- BMW X5 E70 (2006-2013)


Code OEM : 63-13-7-171-008

INSTRUCTIONS:

- Remove your side marker, pushing and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, and connect it to the New one, Repeat the same operation on the CONTRARY.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT



We do not take responsibility for: erroneous purchases-violations of regulations or laws of any state-damages, which could cause you, third parties or the same article. as we describe every single specification in detail.

COMPATIBILITY:

- BMW X5 E70 (2006-2013)


Code OEM : 63-13-7-171-008

INSTRUCTIONS:

- Remove your side marker, pushing and sliding it forward or backward (IT WILL SPIT)

- Disconnect the socket, and connect it to the New one, Repeat the same operation on the CONTRARY.


FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION BY AN EXPERT



We do not take responsibility for: erroneous purchases-violations of regulations or laws of any state-damages, which could cause you, third parties or the same article. as we describe every single specification in detail.

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for BMW Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)