COMPATIBILITY:

ATTENTION to the Version, NO SEATING with: Armrest and Integrated Belts, Non-Removable Headrest, Ergonomic Sporting

- Suitable for Kia Stonic

- NOT COMPATIBLE With Cars with Central Rear Armrest


ASSEMBLY:

" For a correct installation it is strongly recommended to always contact an expert in the sector "
" Some Stages may be slightly different, from Car to Car "


1) INSTALLATION OF FRONT SEATS
- Tilt the Backrest
- Place the appropriate cover on the Seat, aligning it as best as possible
- Bring the Elastics behind the Seat, passing them between the Back and the Seat
- Tighten and Fix the Side Elastics of the Seat between the Side Plastics of the Seat with the Help of a Flat Tip Screwdriver (or a similar tool)
- Make sure the Cover is Aligned Correctly with the Seat
- Tighten the elastics previously brought behind the seat and fix them under the seat, using the special metal hooks supplied
- Tension The Front Elastic Bands Of The Seat And Fix Them Under The Seat, Using The Special Metal Hooks Provided
- Repeat the operation on the Second Seat

2) INSTALLATION OF THE FRONT BACKREST
- ATTENTION: If the car has airbags, Make sure that the "Airbag" label of the seat and the seat cover are on the same side (to understand the exact cover of the driver and passenger seat)
- Remove the headrests
- Insert the Seat Cover on the Backrest and align it in the best way
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch the elastic bands from the back of the seat by pulling the end of the seat cover to which they are anchored, to give it a perfect adherence
- Fix the Elastics under the Seat, using the Special Metal Hooks Provided
- Make an X-shaped cut with scissors in the holes of the headrests and bring out the Plastic Arrangements, pushing the cut part under the Arrangements themselves
- Repeat the operation on the Second Backrest

3) HEADREST INSTALLATION
- Reinstall the Headrests in the Seat
- Slide the Hooded Cover over the Headrest and Line it up

4) REAR SEAT INSTALLATION
- Remove the Rear Seat Cushion (most cars are set up to Release the Rear Seat)
- Insert the seat cover on the seat and align it in the best way
- Tension and Fix the Elastics in Opposite Way to each other under the Seat, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)

5) REAR BACKREST INSTALLATION
- Remove the headrests
- Insert the seat cover on the backrest, under the seat belts, and align it in the best way
- Lower the Backrest
- Bring the elastics of the front part behind the seat, passing them between the backrest and the seat
- Stretch and Fix the Elastics in Opposite Way Behind the Back, using the Special Metal Hooks Provided, trying to keep them as parallel as possible
- For a perfect look it is necessary to always align each end of the seat cover with the seat itself (e.g. corner to corner, top edge to top edge)


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

For KIA STONIC (from 2017)

HANDRAILS NECESSARILY:

- Maximum distance between one and the other 110CM


ASSEMBLY:

- Insert the lock key to remove the side covers and access the screws below
- Take a screwdriver and unscrew the screws, to make the feet open as much as possible
- Position the Roof Bars by hooking them to the Longitudinal Handrails
- Center the bars on the rails
- Tighten the screws of each foot until it locks correctly WITHOUT FORCE EXCESSIVELY
- Close the side covers by locking them with the key lock




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Kia Stonic (from 2017), with Tires:

185/65 R15
195/55 R16

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY:

- KIA STONIC (from 2017) with PROJECTOR HEADLIGHTS, Low + High Beam


FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

- ADAPTERS:

All cars that do not have the STANDARD LOCKING CLIP to lock the halogen bulb, may need simple ADAPTERS; found them in OUR STORE.
IMPORTANT: Their compatibility could not always depend on the model of your car; it depends mainly on the LOCKING SYSTEM of the halogen bulbs of your headlight.

COMPATIBILITY:

- Specific for Kia Stonic


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Specific for Kia Stonic


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Kia Stonic (from 2017), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- KIA

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- KIA

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- ALL KIA

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- ALL KIA

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Suitable for KIA Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for KIA Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for KIA Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- For KIA Cars

It is applicable on any vehicle with an Indentation on the bumper where it will be possible to fix the bracket (LOOK AT THE PHOTO).



ASSEMBLY:

- Put the plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the Screws

- Remove the plate and apply it on the new plate holder

- Apply the chromed frame and Fix it with the 4 screws supplied




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For KIA Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For KIA Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For KIA Cars

It is applicable on any vehicle with an indentation on the bumper, where it will be possible to fix the bracket (WATCH PHOTO).



ASSEMBLY:

- Put the relocation plate holder where you want to apply it, marking the points where you will need to pierce the bumper

- Once the holes have been made, fix the plate holder with the metal plate and the bolts supplied

- Remove the plate and apply it on the new relocation plate holder (1 hole may be required on the plate)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- On Tyres External Edging of your Kia


APPLICATION: 1 With a Sponge, Cloth or Brush - 2 With a Spray Bottle
'' IT IS POSSIBLE TO APPLY IT WITHOUT DILUTING IT or with a little water, having a MORE INTENSE EFFECT with a more Strong colour"

1
- Thoroughly clean the tires before application
- Dilute 50Ml of Concentrate in 200Ml of Water in a Plastic Bucket
- Apply the product with a sponge, cloth or brush
- Wait for Drying

2
- Thoroughly clean the tires before application
- Dilute 1 Part Concentrate in 2-4 Parts Water and Insert it into a Spray Applicator
- Apply the product with a spray bottle
- Wait for Drying




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
We trust in your common sense.

COMPATIBILITY:

- On Bodywork, Rubber, Plastics, Metals "After Washing" of your Kia
- Can be used on previously treated or waxed bodywork without worrying about damaging any layers, on the contrary it reinforces them
- Do not use on glass or mirrors


APPLICATION:

- Spray the Vehicle with Water or Wash it
- Thoroughly dry the car
- Dilute 50ml of Nanotechnological Hydro Wax in 450ml of water
- Apply the product with a professional sponge
- Rinse with Clean Water
- Polish with a clean microfiber cloth




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
We trust in your common sense.

COMPATIBILITY:

- For Kia Stonic (from 2017)
- Front or rear Windshield


APPLICATION:

- Open folding Sunshade and install from the inside of the windshield with the silver side facing outwards.
- Fit the Sunshade Between the End of the Windscreen and the Contrast Sun Visors, Open to Contrast.
- For the Closure it is necessary to form an 8 with the 2 folded circular rings and finally fold it back on itself.
- Place it in the case.


We do not assume responsibility for: incorrect purchases, damage that could be caused to you, to third parties, to the vehicle or to the item itself, as we describe every single specification in detail. We trust in your common sense.

COMPATIBILITY:

- Wheels Vehicles, including Kia
- Nuts 17, 19, 21, 23

USE:

1) The bolts must be unscrewed before lifting the car, on a flat, stable and safe surface.
2) Insert the jack under the frame in the position indicated in the use and maintenance handbook.
3) Raise the jack just enough to tension it in the right position to support the car but without lifting it off the ground.
4) Remove the hubcap and loosen the nuts by turning the cross wrench counterclockwise.
5) The tire must be left in contact with the ground because in this way the force applied makes the nuts turn but not the wheel, which remains blocked by the ground.
6) The nuts must not be unscrewed completely but you must limit yourself to overcoming the resistance of the tightening.
7) Raise the car, completing the operation of unscrewing the bolts and removing the wheel which must be completed by hand.

The same operation must be done in reverse when refitting the replaced wheel, tightening the bolts last, to be carried out when the vehicle is already on the ground.

COMPATIBILITY:

- On Bodywork, Rubber, Plastics, Metals of your Kia
- Can be used on previously treated or waxed bodywork without worrying about affecting any layers


APPLICATION: 1) Possible Manual Application 2) Possible use With Foam Sprayer


1) Manual Application

- Dilute 1 Part of Active Foam in 8 Parts of Water
- Evenly apply a good layer of foam using a washing glove or sponge
- Wait 5 Minutes
- Rinse thoroughly with a high pressure cleaner


2) Application with Foam Sprayer

- Dilute 1 Part of Active Foam in 8 Parts of Water
- Evenly apply a good layer of foam using a foam sprayer
- Wait 5 Minutes
- Rinse thoroughly with a high pressure cleaner





Even if simple and intuitive FOR OPTIMAL USE, WE ALWAYS RECOMMEND THE APPLICATION OF OUR PRODUCTS BY AN EXPERT, Always Checking The Risk Label relating to Dangerous Substances, as any form of Contact could be dangerous. We trust in your common sense.

We do not assume responsibility for: erroneous purchases - violations of regulations or laws of any state - damages that you could cause to yourself, to third parties, to the Vehicle or to the article itself, as we describe every single specification in detail.