COMPATIBILITY:

VOLKSWAGEN GOLF 3 VARIANT/SPORTCOMBI Station Wagon (94-98)
VOLKSWAGEN GOLF 4 VARIANT/SPORTCOMBI Station Wagon (99-07)
VOLKSWAGEN GOLF 5 VARIANT/SPORTCOMBI Station Wagon (07-10)
VOLKSWAGEN GOLF 6 VARIANT/SPORTCOMBI Station Wagon (10-13)
VOLKSWAGEN GOLF 8 VARIANT/SPORTCOMBI Station Wagon (from 2021)
VOLKSWAGEN GOLF PLUS (05-14)
VOLKSWAGEN GOLF SPORTSVAN (from 2014)


HANDRAILS NECESSARILY:

- Maximum distance between one and the other 110CM


ASSEMBLY:

- Insert the lock key to remove the side covers and access the screws below
- Take a screwdriver and unscrew the screws, to make the feet open as much as possible
- Position the Roof Bars by hooking them to the Longitudinal Handrails
- Center the bars on the rails
- Tighten the screws of each foot until it locks correctly WITHOUT FORCE EXCESSIVELY
- Close the side covers by locking them with the key lock




Although simple and intuitive FOR AN OPTIMAL ASSEMBLY, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Volkswagen Golf VIII (from 2019), with Tires:

205/50 R17
225/40 R18
235/35 R19

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY:

- Volkswagen Golf 8 from 2019
- Volkswagen Golf 8 GTE GTD GTI from 2019


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Volkswagen Golf 8 from 2019
- Volkswagen Golf 8 GTE GTD GTI from 2019


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Volkswagen Golf 8 from 2019
- Volkswagen Golf 8 GTE GTD GTI from 2019


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Specific for Volkswagen Golf


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- Specific for Volkswagen Golf


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For Volkswagen Golf 8 (from 2019), with Automatic Gearbox


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers
3) To assemble the foot rest proceed as follows:

- Remove the Engine Compartment Opening Handle
- Remove the hook that holds the Engine Compartment Opening Handle securely
- Unhook and Remove the Engine Compartment Opening Handle by pulling it outwards
- Remove the Round Rubber Hole Cover
- Remove the Clip Screw with a Fixed Screwdriver, Rotating it Anticlockwise to Unhook and Extract it
- Now it is possible to unhook the plastic side part by extracting the existing foot rest
- Fit the new Interlocking Foot Rest and close everything by repeating the operations already carried out in reverse



Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Volkswagen Golf VIII (from 2019), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- For Volkswagen Golf 8 (from 2019), With Manual Gearbox


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers
3) To assemble the foot rest proceed as follows:

- Remove the Engine Compartment Opening Handle
- Remove the hook that holds the Engine Compartment Opening Handle securely
- Unhook and Remove the Engine Compartment Opening Handle by pulling it outwards
- Remove the Round Rubber Hole Cover
- Remove the Clip Screw with a Fixed Screwdriver, Rotating it Anticlockwise to Unhook and Extract it
- Now it is possible to unhook the plastic side part by extracting the existing foot rest
- Fit the new Interlocking Foot Rest and close everything by repeating the operations already carried out in reverse




Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- Suitable for VOLKSWAGEN Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for VOLKSWAGEN Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Suitable for VOLKSWAGEN Steering Wheel


ASSEMBLY:

- Adhere the 2 Inserts to the Sides of the Steering Wheel, Interlocking


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- For Volkswagen Golf 8 (from 2019)
- Front or rear Windshield


APPLICATION:

- Open folding Sunshade and install from the inside of the windshield with the silver side facing outwards.
- Fit the Sunshade Between the End of the Windscreen and the Contrast Sun Visors, Open to Contrast.
- For the Closure it is necessary to form an 8 with the 2 folded circular rings and finally fold it back on itself.
- Place it in the case.


We do not assume responsibility for: incorrect purchases, damage that could be caused to you, to third parties, to the vehicle or to the item itself, as we describe every single specification in detail. We trust in your common sense.

COMPATIBILITY:

- Wheels Vehicles, including Volkswagen
- Nuts 17, 19, 21, 23

USE:

1) The bolts must be unscrewed before lifting the car, on a flat, stable and safe surface.
2) Insert the jack under the frame in the position indicated in the use and maintenance handbook.
3) Raise the jack just enough to tension it in the right position to support the car but without lifting it off the ground.
4) Remove the hubcap and loosen the nuts by turning the cross wrench counterclockwise.
5) The tire must be left in contact with the ground because in this way the force applied makes the nuts turn but not the wheel, which remains blocked by the ground.
6) The nuts must not be unscrewed completely but you must limit yourself to overcoming the resistance of the tightening.
7) Raise the car, completing the operation of unscrewing the bolts and removing the wheel which must be completed by hand.

The same operation must be done in reverse when refitting the replaced wheel, tightening the bolts last, to be carried out when the vehicle is already on the ground.