COMPATIBILITY:

- COMPATIBLE WITH VOLKSWAGEN CARS WITH SEQUENTIAL AUTOMATIC TRANSMISSION, AND STEERING WHEEL LEVERS (See Photo 2):

- Volkswagen Passat B8 R-Line 2014-2019

**Attention: ONLY for R-Line steering wheel**


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Volkswagen Passat B8 (from 2014), with Tires:

215/60 R16
215/55 R17
235/45 R18
235/40 R19

INSTALLATION:

- 1 Take a sock and insert it into the upper part of the tire, making sure that it adheres well to the rear area of the tire.
- 2 Drive a little forward with the car, to repeat the operation and fix the sock also in the part of the rubber that previously touched the road surface.
- 3 drive for a hundred meters at low speeds, stopping the car again to check that the device has been installed correctly.
- 4 continue the journey in safety taking into account the Maximum Speed of 50Km-h.


We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damage, which you could cause to you, to third parties or to the item itself, as we detail every single specification, we trust in your common sense.

COMPATIBILITY:

- For Lowbeam VOLKSWAGEN PASSAT B8 (from 2014)


FOR AN OPTIMUM MOUNTING, WE RECOMMEND:

- DISMOUNTING YOUR HALOGEN BULBS

- CHECK FIRST: Connect only the led socket (PLUG AND PLAY ); if there is not any problem, proceed with mounting operations.

- BLOCK ONLY THE LED RING: Remove the led ring from the led bulb using circular motion and fix in the locking clip of the halogen bulb.

- IMPORTANT: THE LIFE OF THE LED DEPENDS ON THE HEATSINK: Open the copper heatsink as much as possible, till you obtain a "rose shape" heatsink. Extend each heatsink, don' t be afraid to use force.

- CONNECT THE SOCKET AND LOCK THE BULB: Put the bulb inside its ring that you had previously fixed, and lock it using circular motion.




NON-STANDARD CASES


- DEEPER DUST CAPS:

Being a TRANSFORMATION kit, and not replacement bulbs, it has bigger dimensions.
If the installation of the kit does not allow to close the headlight anymore, visit our store for DEEPER DUST CAPS.

- ADAPTERS:

All cars that do not have the STANDARD LOCKING CLIP to lock the halogen bulb, may need simple ADAPTERS; found them in OUR STORE.
IMPORTANT: Their compatibility could not always depend on the model of your car; it depends mainly on the LOCKING SYSTEM of the halogen bulbs of your headlight.

COMPATIBILITY:

- Volkswagen Passat B8 from 2019 (Facelift)


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Volkswagen Passat B8 from 2019 (Facelift)


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Volkswagen Passat B8 from 2019 (Facelift)


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Specific for Volkswagen Passat


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

It is possible to cut and then shorten the spoiler from the side where the wire is not present, but this modification will inevitably involve the decentralization of the Dynamic LED function.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- COMPATIBLE WITH VOLKSWAGEN CARS WITH SEQUENTIAL AUTOMATIC TRANSMISSION, AND STEERING WHEEL LEVERS (See Photo 2):

- Volkswagen Passat B8 R-Line 2014-2019

**Attention: ONLY for R-Line steering wheel**


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- COMPATIBLE WITH VOLKSWAGEN CARS WITH SEQUENTIAL AUTOMATIC TRANSMISSION, AND STEERING WHEEL LEVERS (See Photo 2):

- Volkswagen Passat B8 R-Line 2014-2019

**Attention: ONLY for R-Line steering wheel**


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- COMPATIBLE WITH VOLKSWAGEN CARS WITH SEQUENTIAL AUTOMATIC TRANSMISSION, AND STEERING WHEEL LEVERS (See Photo 2):

- Volkswagen Passat B8 R-Line 2014-2019

**Attention: ONLY for R-Line steering wheel**


ASSEMBLY:

- Turn the steering wheel over and locate the pin under the gear lever
- Gently extract and remove the gear lever pin using a pair of pliers
- Gently remove the cotter pin that secures the original gear lever to the steering wheel, replace it with your new aluminum paddle, then reinstall the pin and push it all the way in.
- Repeat for the other side



(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- COMPATIBLE WITH VOLKSWAGEN CARS WITH SEQUENTIAL AUTOMATIC TRANSMISSION, AND STEERING WHEEL LEVERS (See Photo 2):

- Volkswagen Passat B8 R-Line 2014-2019

**Attention: ONLY for R-Line steering wheel**


ASSEMBLY:

- Adhere the Pads on the Current Gear Levers to the Steering Wheel, using the Sticker on the Front.
- Tighten the screws to ensure that they anchor perfectly to the Actual Pads.


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- COMPATIBLE WITH VOLKSWAGEN CARS WITH SEQUENTIAL AUTOMATIC TRANSMISSION, AND STEERING WHEEL LEVERS (See Photo 2):

- Volkswagen Passat B8 R-Line 2014-2019

**Attention: ONLY for R-Line steering wheel**


ASSEMBLY:

- Adhere the Pads on the Current Gear Levers to the Steering Wheel, using the Sticker on the Front.
- Tighten the screws to ensure that they anchor perfectly to the Actual Pads.


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- COMPATIBLE WITH VOLKSWAGEN CARS WITH SEQUENTIAL AUTOMATIC TRANSMISSION, AND STEERING WHEEL LEVERS (See Photo 2):

- Volkswagen Passat B8 R-Line 2014-2019

**Attention: ONLY for R-Line steering wheel**


ASSEMBLY:

- Adhere the Pads on the Current Gear Levers to the Steering Wheel, using the Sticker on the Front.
- Tighten the screws to ensure that they anchor perfectly to the Actual Pads.


(Although Simple and Intuitive, WE ALWAYS RECOMMEND ASSEMBLY BY AN EXPERT IN THE SECTOR, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS DO NOT RECOMMEND DO IT YOURSELF)

COMPATIBILITY:

- Specific for Volkswagen Passat


ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Connect the 3 Wires, Respectively:

BLACK: Connect to Neutral Ground
RED: Connect to the Base Lighting System
WHITE: Connect to the STOP light switch-on function

(For a perfect fixing, use a bodywork thermal hair dryer)

For a perfect fit, it is possible to cut and then shorten the spoiler from the side where there is no clable; but, ATTENTION, once the modification has taken place, the Warranty and Right of Return will expire.





FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For Volkswagen PASSAT B8 (from 2014), With Left Double Exhaust

- "NO" For Versions That alreday Have Standard Exhausts


ASSEMBLY:

1) Measure the Bumper Opening to Make sure the New Exhaust Tips comes out
2) Slide the New Terminals onto the Existing Exhaust Tips, up to the joint point
(If desired, thanks to SS304 steel, it is possible to give a Welding Point)






Although mouting is simple and intuitive, FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT.
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- For Volkswagen PASSAT B8 (from 2014), With Left Double Exhaust

- "NO" For Versions That Have Standard Chrome Exhausts


ASSEMBLY:

1) Measure the Bumper Opening to Make sure the New Exhaust Tips comes out
2) Slide the New Terminals onto the Existing Exhaust Tips, up to the joint point
(If desired, thanks to SS304 steel, it is possible to give a Welding Point)





Although mouting is simple and intuitive, FOR AN OPTIMAL MOUNTING, WE ALWAYS RECOMMEND THE INSTALLATION OF OUR ITEMS BY AN EXPERT.
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- VW Passat with Wheels Between 14 Inches and 18 Inches
- Tire Width not Exceeding 245


USE:

- Use of Wheel Covering, Storage, Transport
- Insert the tire inside the bag by rolling it on it
- Close the strap with the internal Velcro
- Close Clips
- Insert Pins Into The Outer Hook Pocket

COMPATIBILITY:

- Universal | Cars, SUVs, Vans
- Reclining Seats
- Seats with Integrated AIRBAG


INSTALLATION:

- Remove the headrest, pulling it out completely
- Position the appropriate cover on the Seat, aligning it as best as possible
- Bring the central elastic behind the seat, inserting it on the backrest and making it go down to the height of the seat
- Insert the headrest again making it go through the holes in the seat cover
- Bring the rear elastic of the seat behind the seat, inserting it between the back and the seat
- Behind the seat, stretch the elastic just passed between the back and the seat and fix it under the seat with the hooks present on the front elastic of the seat
- Make sure the Cover is Aligned Correctly with the Seat
- Position the cover for the headrest and hook it vertically to the rear with the hook and the elastic on it.


(Although Simple and Intuitive, ASSEMBLY BY AN EXPERT IN THE SECTOR IS ALWAYS RECOMMENDED, TO AVOID POSSIBLE DAMAGE TO THINGS OR PEOPLE. WE ALWAYS RECOMMEND NOT DO IT YOURSELF)

COMPATIBILITY:

- For Volkswagen Passat B8 (from 2014), Front Windshield
- 9-11 adapters will be provided, including the one suitable for your car


FOR AN OPTIMAL MOUNTING, WE RECOMMEND:

- Although simple, we DO NOT RECOMMEND self-assembly unless in the presence of due assembly skills, as incorrect assembly of this product can cause damage to the windshield, the vehicle and the wiper blade itself.

- RAISE THE ENTIRE ARM: Raise the arm from the windscreen positioning it vertically, the methods for carrying out this operation are specified in the vehicle use and maintenance manual.

- DISCONNECT THE CLAMP: find the hooking clamp and detach the old piece that connects the blade to the Arm, replacing it with one of the adapters present in the newly purchased windscreen wiper blade.

- LOCKING: Install the wiper blade by closing it with the appropriate adapter supplied which you will have to compare in terms of shape and type of closure similar to the previous one already installed.

- CHECK: Place the wiper blades on the windscreen or rear window, checking their stability and positioning before using them.

- FIRST USE: Before using it, it is a good idea to carefully clean the windscreen or rear window with products suitable for removing the impurities accumulated on the glass, as these, although not very visible, could hinder the initial cleaning of the wiper blades, creating lines and at the same time prematurely wearing the new wiper blade.




We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail.

We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.

We trust in your common sense.

COMPATIBILITY:

- VOLKSWAGEN PASSAT

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- VOLKSWAGEN PASSAT

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut off excess parts

- Apply the two terminal parts in Thermal ABS supplied

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.

COMPATIBILITY:

- For Volkswagen Passat B8 (from 2014), with Automatic Gearbox


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers
3) To assemble the foot rest proceed as follows:

- Remove the Engine Compartment Opening Handle
- Remove the hook that holds the Engine Compartment Opening Handle securely
- Unhook and Remove the Engine Compartment Opening Handle by pulling it outwards
- Remove the Round Rubber Hole Cover
- Remove the Clip Screw with a Fixed Screwdriver, Rotating it Anticlockwise to Unhook and Extract it
- Now it is possible to unhook the plastic side part by extracting the existing foot rest
- Fit the new Interlocking Foot Rest and close everything by repeating the operations already carried out in reverse



Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- For Volkswagen Passat B8 (from 2014), With Manual Gearbox


INSTALLATION:

1) Remove the existing rubbers or plastics from the pedals
2) Snap on the new pedal covers
3) To assemble the foot rest proceed as follows:

- Remove the Engine Compartment Opening Handle
- Remove the hook that holds the Engine Compartment Opening Handle securely
- Unhook and Remove the Engine Compartment Opening Handle by pulling it outwards
- Remove the Round Rubber Hole Cover
- Remove the Clip Screw with a Fixed Screwdriver, Rotating it Anticlockwise to Unhook and Extract it
- Now it is possible to unhook the plastic side part by extracting the existing foot rest
- Fit the new Interlocking Foot Rest and close everything by repeating the operations already carried out in reverse



Even if simple and intuitive FOR AN OPTIMUM ASSEMBLY, WE ALWAYS RECOMMEND INSTALLATION OF OUR ITEMS BY AN EXPERT
As we will not take responsibility for the assembled and subsequently detached article.
We trust in your common sense.

COMPATIBILITY:

- VOLKSWAGEN PASSAT

It is applicable on any vehicle: Cars, SUVs, Trucks. Perfect adaptability.



ASSEMBLY:

- Wash and thoroughly clean the surface where the spoiler is to be applied

- Remove the 3M adhesive film, and adhere the spoiler to the desired part

- Cut Posteriorly in large curvatures to facilitate folding

- Cut off excess parts

- Apply the supplied screws

(For a perfect fit, use a thermal body dryer)




FOR OPTIMAL MOUNTING, EVEN IF SIMPLE REPLACEMENT, WE ALWAYS RECOMMEND THE INSTALLATION OF AN EXPERT, as we do not assume responsibility for articles mounted and subsequently detached. We trust in your common sense.